25143
10
Zoom out
Zoom in
Previous page
1/48
Next page
Page 10
Assembly
ALWAYS BE SURE THE TOOL IS
IN THE “OFF” POSITION
BEFORE CHANGING ACCESSORIES, CHANGING
COLLETS OR SERVICING YOUR CORDLESS
ROTARY TOOL.
WARNING
!
COLLET NUT— To loosen, first press shaft lock but-
ton and rotate the collet nut by hand until the lock
engages the shaft preventing further rotation.
Do not engage lock while the
Tool is running.
With the shaft lock engaged, loosen the collet nut by
hand. Change accessories by inserting the new one
into the collet as far as possible to minimize runout
and unbalance. With the shaft lock engaged, finger
tighten the collet nut until the accessory shank is
gripped by the collet.
Avoid excessive tightening
of the collet nut when there is no bit inserted.
COLLETS —
Four different size collets (see illus-
tration), to accommodate different shank sizes, are
available for your Cordless Rotary Tool. To install a
different collet, remove the collet nut and remove
the old collet. Insert the unslotted end of the collet
in the hole in the end of the tool shaft. Replace col-
let nut on the shaft.
Always use the collet which
matches the shank size of the accessory you plan
to use.
Never force a larger diameter shank into a
collet.
BALANCING ACCESSORIES — For precision work,
it is important that all accessories be in good bal-
ance (much the same as the tires on your automo-
bile). To true up or balance an accessory, slightly
loosen collet nut and give the accessory or collet a
1/4 turn. Retighten collet nut and run the Tool. You
should be able to tell by the sound and feel if your
accessory is running in balance. Continue adjusting
in this fashion until best balance is achieved. To
maintain balance on abrasive wheel points, before
each use, with the wheel point secured in the collet,
turn on the Cordless Rotary Tool and run the 415
Dressing Stone lightly against the revolving wheel
point. This removes high spots and trues up the
wheel point for good balance.
!
CAUTION
SHAFT
LOCK
BUTTON
TO LOOSEN
TO TIGHTEN
COLLET
NUT
COLLET
COLLET
NUT
IDENTIFICATION
RINGS
480 1/8"
COLLET
481 3/32"
COLLET
482 1/16"
COLLET
483 1/32"
COLLET
(1/8" Collet is included with your tool)
COLLET IDENTIFICATION CHART — Collet sizes
can be identified by the rings on the back end of
collet.
1/32" Collet has one (1) ring.
1/16" Collet has two (2) rings.
3/32" Collet has three (3) rings.
1/8" Collet has no rings.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 760 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info