Manual Dremel 750 (page 4 of 68) (English, French, Spanish)

25131

Zoom out

Zoom in

1/68

Page 4

Safety Rules for Cordless Rotary Tools

Hold tool by insulated gripping surfaces when per-

forming an operation where the cutting tool may

contact hidden wiring. Contact with a "live" wire will

make exposed metal parts of the tool "live" and shock

the operator.

Use clamps or other practical way to secure and sup-

port the workpiece to a stable platform. Holding the

work by hand or against your body is unstable and may

lead to loss of control.

Accessories must be rated for at least the speed

recommended on the tool warning label. Wheels

and other accessories running over rated speed can

fly apart and cause injury.

If cutting into existing walls or other blind areas

where electrical wiring may exist is unavoidable,

disconnect all fuses or circuit breakers feeding this

worksite.

Before changing accessories remove battery pack.

Accidental starting may occur because battery tools

with a battery inserted are in the operative condition.

Be aware of the switch location, when placing the

tool down or when picking the tool up. You may acci-

dentally activate the switch.

Always hold the tool with two hands during astart-

up.

The reaction torque of the motor can cause the tool to

twist.

Always wear safety goggles and dust mask. Use

only in well ventilated area. Using personal safety

devices and working in safe environment reduces risk

of injury.

After changing the bits or making any adjustments,

make sure the collet nut and any other adjustment

devices are securely tightened. Loose adjustment

device can unexpectedly shift, causing loss of control,

loose rotating components will be violently thrown.

Do not reach in the area of the spinning bit. The

proximity of the spinning bit to your hand may not

always be obvious.

Allow brushes to run at operating speed for at least

one minute before using wheel. During this time no

one is to stand in front or in line with the brush.

Loose bristles or wires will be discharged during the

run-in time.

Wire and bristle brushes must never be operated at

speeds greater than 15,000/min. Direct the dis-

charge of the spinning wire brush away from you.

Small particles and tiny wire fragments may be dis-

charged at high velocity during the “cleaning” action

with these brushes and may become imbedded in

your skin. Bristles or wires will be discharged from

the brush at high speeds.

"Wear protective gloves and face shield with wire or

bristle brushes. Apply wire or bristle brushes light-

ly to the work as only the tips of the wire/bristles do

the work.

“Heavy” pressure on bristles will cause the

wire or bristle to become overstressed, resulting in a

wiping action and will cause the bristles/wire to be

discharged."

Carefully handle both the tool and individual grind-

ing wheels to avoid chipping or cracking. Install a

new wheel if tool is dropped while grinding. Do not

use a wheel that may be damaged. Fragments from

a wheel that bursts during operation will fly away at

great velocity possibly striking you or bystanders.

Never use dull or damaged bits. Sharp bits must be

handled with care. Damaged bits can snap during

use. Dull bits require more force to push the tool,

possibly causing the bit to break.

Use clamps to support workpiece whenever practi-

cal. Never hold a small workpiece in one hand and

the tool in the other hand while in use. Allow for

sufficient space, at least 6", between your hand and

the spinning bit. Round material such as dowel rods,

pipes or tubing have a tendency to roll while being

cut, and may cause the bit to “bite” or jump toward

you. Clamping a small workpiece allows you to use

both hands to control the tool.

DM 2610925743 02-05 2/7/05 9:33 AM Page 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 750 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel 750 Manual

Product: