Manual Dremel 400seriesXPR (page 9 of 72) (English, French, Spanish)

25125

Zoom out

Zoom in

1/72

OPERATION

ASSEMBLY (CONTINUED)

Learning To Use the Rotary Tool

Getting the most out of your rotary tool is a

matter of learning how to let the speed and

the feel of the tool in your hands work for you.

The first step in learn-

ing to use the rotary

tool is to get the “feel”

of it. Hold it in your

hand and feel its

weight and balance.

Feel the taper of the

housing. This taper permits the tool to be

grasped much like a pen or pencil. The

unique comfort grip on the nose allows for

added comfort and control during use.

Always hold the tool

away from your face.

Accessories can be damaged during

handling and can fly apart as they come

up to speed. This is not common, but it

does happen.

When holding tool, do not

cover the air vents with

your hand. Blocking the air vents could

cause the motor to overheat.

IMPORTANT!

Practice on scrap material first

to see how the tool’s high-speed action per-

forms. Keep in mind that your rotary tool will

perform best by allowing the speed, along

with the correct Dremel™ accessory and

attachment, do the work for you. Do not put

pressure on the tool during use, if possible.

Instead, lower the spinning accessory lightly

to the work surface and allow it to touch the

point at which you want to begin.

Concentrate on guiding the tool over the

work using very little pressure from your

hand. Allow the accessory to do the work.

WARNING

CAUTION

Usually it is better to make a series of pass

es with the tool rather than to do the entire

job with one pass. Agentle touch gives the

best control and reduces the chance for

error.

For best control in close work, grip the rotary

tool like a pencil between your thumb and

forefinger.

The “golf” grip method is used for more aggres-

sive operations such as grinding or cutting.

Keyless Chuck

The keyless chuck is used in place of the stan

dard collet and collet nut to easily and quickly

remove and install some accessories.

The keyless chuck holds various accessories

with shank sizes 1/32" to 1/8" and is intended

for light duty accessories such as drill bits,

sanding drums, polishing accessories, wire

and bristle brushes and cut-off wheels.

1. See steps 1—3, Changing Collets on

page 7 to install the keyless chuck.

2. Thread the keyless chuck onto the rotary

tool shank.

3. Use the supplied wrench to complete-

ly tighten the keyless chuck if you are

unable to apply sufficient tightening

pressure to hold the bit or accessory.

Keyless Chuck

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 400seriesXPR in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel 400seriesXPR Manual

Product: