Manual Dremel 4000 (page 20 of 92) (English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish)

488599

Zoom out

Zoom in

1/92

c. Do not position your body in the area where the power tool

will move if kickback occurs. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point of

snagging.

d. Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e. Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC TO GRINDING

AND ABRASIVE CUTTING-OFF OPERATIONS

a. Use only wheel types that are recommended for your power

tool and the speciﬁc guard designed for the selected wheel.

Wheels for which the power tool was not designed cannot be

adequately guarded and are unsafe.

b. Wheels must be used only for recommended applications. For

example: do not grind with the side of cut-off wheel. Abrasive

cut-off wheels are intended for peripheral grinding, side forces

applied to these wheels may cause them to shatter.

c. Always use undamaged wheel ﬂanges that are of correct

size and shape for your selected wheel. Proper wheel flanges

support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be different from

grinding wheel flanges.

d. Do not use worn-down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

ADDITIONAL SAFETY WARNINGS SPECIFIC TO

ABRASIVE CUTTING OFFOPERATIONS

a. Do not "jam" the cut-off wheel or apply excessive pressure. Do

not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility of kickback

or wheel breakage.

b. Do not position your body in line with and behind the rotating

wheel. When the wheel, at the point of operation, is moving

away from your body, the possible kickback may propel the

spinning wheel and the power tool directly at you.

c. When wheel is binding or when interrupting a cut for any reason,

switch off the power tool and hold the power tool motionless

until the wheel comes to a complete stop. Never attempt to

remove the cut-off wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate and take

corrective action to eliminate the cause of wheel binding.

d. Do not restart the cutting operation in the workpiece. Let the

wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is

restarted in the workpiece.

e. Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend

to sag under their own weight. Supports must be placed

under the workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

f. Use extra caution when making a "pocket cut" into existing

walls or other blind areas. The protruding wheel may cut gas

or water pipes, electrical wiring or objects that can cause

kickback.

SAFETY WARNINGS SPECIFIC TO

WIRE BRUSHING OPERATIONS

a. Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires by

applying excessive load to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

b. If the use of a guard is recommended for wire brushing, do

not allow any interference of the wire wheel or brush with the

guard. Wire wheel or brush may expand in diameter due to

work load and centrifugal forces.

c. Do not exceed 15,000 RPM when using wire brushes.

ENVIRONMENT

DISPOSAL

The machine, accessories and packaging should be sorted for

environmental-friendly recycling.

ONLY FOR EC COUNTRIES

Do not dispose of power tools with household waste!

According the European Guideline 2002/96/EC for

Waste Electrical and Electronic Equipment and its

implementation into national law, power tools that are

no longer usable must be collected separately and

disposed of in an environmentally-correct manner.

SPECIFICATIONS

GENERAL SPECIFICATIONS

Voltage Rating ........... 230-240 V, 50-60 Hz

Related Power ........... 175 W

Rated Speed (n) . . . . . . . . . . 35,000 RPM

Collet Capacity .......... 0.8mm, 1.6mm, 2.4mm,

3.2mm

Class II construction .... Double insulated construction tools

(PICTURE 5)

EXTENSION CORDS

Use completely unrolled and safe extension cords with a

capacity of 5 Amps.

ASSEMBLY

ALWAYS UNPLUG MULTITOOL BEFORE CHANGING ACCESSORIES,

CHANGING COLLETS, OR SERVICING THE TOOL.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 4000 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 1,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel 4000 Manual

Product: