25111

Dremel 395T6 Manual

17
Zoom out
Zoom in
Previous page
1/92
Next page
P
age 17
Right Angle Attachment 575
Before you begin, remove the black protective cap on
your attachment. If cap does not slide off easily, insert
the shank portion of any accessory through the
housing opening of the attachment to hold shaft from
rotating. Then twist off. Figure 1.
Do not use the rotary tool shaft
lock button when changing
accessories on the attachment. Internal damage to
the attachment may occur.
Remove the housing cap from your existing rotary
tool as shown in fig. 2. Then press the shaft lock
button on your rotary tool, unscrew the collet nut and
remove the collet.
Set your collet nut and collet aside it will be
reinstalled later in step 4.
Install the drive adapter, included with your right
angle attachment, on the motor shaft as shown in
fig.3 and tighten.
Do not over tighten drive
adapter. Tighten the drive adapter
finger tight and then tighten an additional 1/3 turn
with the wrench. (Wrench included with your rotary
tool kit)
Screw the attachment onto your rotary tool. Hand
tighten only. Reassemble the collet and the collet nut
from step 2, on to the output shaft of the attachment.
Figure 4.
The right angle attachment can be oriented on your
rotary tool in 12 different positions. The attachment
should be positioned so the on/off speed control
switch is easy to access.
To reposition, unscrew the collar from the attachment
until disengaged. Slide the attachment off. Then,
reposition, slide the attachment back on the tool and
retighten the collar. Figure 5.
To change an accessory, insert the shank portion of
any accessory (3,2 mm recommended) through the
housing opening of the attachment to hold the shaft
from rotating. With the shaft secured, loosen the
collet nut and insert an accessory as deeply as
possible to avoid wobble during use. You may need to
pull back the shank from the housing opening to
provide clearance while inserting the accessory.
Figure 6.
Attachment can become hot after
prolong usage.
1
2
3
4
5
CAUTION
!
CAUTION
!
FIG. 1 FIG. 2 FIG. 3
FIG. 4 FIG. 5
FIG. 6
!
WARNING
DM 2610925474 10-04 10/19/04 3:40 PM Page 17
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 395T6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 395T6 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info