25111
14
Zoom out
Zoom in
Previous page
1/92
Next page
Do not operate the flexible shaft
with a sharp bend. This can
generate excessive heat and will reduce tool and flex-
shaft life. The recommended minimum is 5" radius.
Contents of 225 Flex-Shaft Attachment:
Qty. Description
1 Flex-Shaft Assembly (42" long)
1 Driver Cap
Page 14
#560
Drywall Cutting Bit
For use in drywall.
• When inserting the #560 bit into your Rotary Tool,
make sure that the bit has been inserted as far as
possible.
• When using a template (outlet box) behind the
drywall, use the drywall bit #560, cutting in a counter-
clockwise direction.
#561
Multipurpose Cutting Bit
For use in wood, plastics, drywall, fiberglass, vinyl
or aluminum siding, acoustical tile and laminates.
• When inserting the #561 bit into your Rotar
y T
ool,
make sure that the bit has been inserted as far as
possible.
• When making freehand cuts in Drywall, example
repairing a hole in drywall, use the Multipurpose bit
#561,cutting in a clockwise direction.
• When using #561, Multipurpose Cutting Bit, start the
bit into the material at a 45 degree angle and then
slowly bring it to a 90 degree angle to begin the cut.
#562
Tile Cutting Bit
For use on wall tile, cement board and plaster
• When inserting the #562 bit into your MultiPro tool,
it is ver
y important that 1/16”-1/8” of smooth shank
remains visible above the collet.
• When using #562, T
ile Cutting Bit, start the bit into
the material at a 45 degree angle and then slowly
bring it to a 90 degree angle to begin the cut.
• NOT FOR USE ON FLOOR TILE
Cutting Guide 565
The Cutting Guide 565 (sold separately) comes
completely assembled and ready to use. For use in a
variety of materials up to 3/4” thick. Match the bit
type to the material to be cut. Always hold the tool
firmly, using slow steady pressure to make cuts.
To attach, follow the four steps shown below.
Important: When viewing the tool from the top, the
bit rotates clockwise. Feed direction of cutting
must be counter-clockwise.
WARNING
!
5" RADIUS
3/4
1/2
1/4
0
3/4
1/2
1/4
0
Step 1 Step 2
Step 3 Step 4
Assembly & Operation of Attachments - (Cont.)
DM 2610925474 10-04 10/19/04 3:40 PM Page 14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 395T6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 395T6 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info