Manual Dremel 395T6 (page 8 of 92) (English, French, Spanish)

25111

Zoom out

Zoom in

1/92

Page 8

COLLET NUT — To loosen, first press shaft lock

button and rotate the shaft by hand until the lock

engages the shaft preventing further rotation.

Do not engage lock while the

Rotary Tool is running.

With the shaft lock engaged use the collet wrench to

loosen the collet nut if necessary. The collet nut must

be loosely threaded on when inserting an accessory.

Change accessories by inserting the new one into the

collet as far as possible to minimize runout and

unbalance. With the shaft lock engaged, finger tighten

the collet nut until the accessory shank is gripped by

the collet.

Avoid excessive tightening of the collet

nut when there is no bit inserted.

COLLETS —

Four different size collets (see illus-

tration), to accommodate different shank sizes, are

available for your Rotary Tool. To install a different

collet, remove the collet nut and remove the old collet.

Insert the unslotted end of the collet in the hole in the

end of the tool shaft. Replace collet nut on the shaft.

Always use the collet which

matches the shank size of the

accessory you plan to use. Never force a larger

diameter shank into a collet.

Note: Some rotary tool kits may not include all four

collets sizes.

BALANCING ACCESSORIES — For precision work, it

is important that all accessories be in good balance

(much the same as the tires on your automobile). To

true up or balance an accessor

y, slightly loosen collet

nut and give the accessory or collet a 1/4 turn. Re-

tighten collet nut and run the Rotary Tool. You should

be able to tell by the sound and feel if your accessory

is running in balance. Continue adjusting in this

fashion until best balance is achieved. To maintain

balance on abrasive wheel points, before each use,

with the wheel point secured in the collet, turn on the

Rotary Tool and run the 415 Dressing Stone lightly

against the revolving wheel point. This removes high

spots and trues up the wheel point for good balance.

The hanger is provided for the use of hanging your

tool while using the flex-shaft or for storage. If you do

not use the hanger, remove it from the tool and snap

it back into place underneath the cord so it will be out

of the way while the tool is in use.

DREMEL KEYLESS CHUCK

Use only with black chuck #4486. Other chucks may

not allow accessory bit to be tightened fully.

The keyless chuck holds various accessories with

shank sizes 1/32" to 1/8" and is intended for light duty

accessories such as drill bits, sanding drums,

polishing accessories, wire and bristle brushes and

cut-off wheels. The keyless chuck allows you to

change accessories frequently, quickly and easily.

There are some applications which can generate high

forces on the bit or if you are unable to generate

finger tightening pressure sufficient to secure the bit

you must use the supplied wrench to assist in

securing the bit.

Attaching the Keyless Chuck and Accessory Bit

Read and understand the manual for use of the

keyless chuck with the tool.

Insert and securely tighten the

shank of the accessory well within the jaws of the

chuck. If an accessory is not properly gripped within

the jaws of a chuck it may loosen and fly out during

COLLET

NUT

TO LOOSEN

TO TIGHTEN

COLLET

WRENCH

Always unplug Rotary Tool

before changing accessories,

changing collets or servicing your Rotary Tool.

SHAFT LOCK

BUTTON

COLLET NUT

KEYLESS CHUCK

IDENTIFICA

TION

RINGS

480

1/8"

COLLET

481

3/32"

COLLET

482

1/16"

COLLET

483

1/32"

COLLET

CAUTION

Assembly

WARNING

COLLET IDENTIFICATION CHART

Collet sizes can be identified by the rings on the back

end of collet.

1/32

" Collet has one (1) ring.

1/16" Collet has two (2) rings.

3/32" Collet has three (3) rings.

1/8" Collet has no rings.

DM 2610925474 10-04 10/19/04 3:39 PM Page 8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 395T6 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dremel 395T6 Manual

Product: