25103
52
Zoom out
Zoom in
Previous page
1/68
Next page
Página 52
No acople el cierre mientras la
Herramienta Giratoria está en
marcha.
PORTAHERRAMIENTAS Hay portaherramientas de
cuatro tamaños distintos (vea la ilustración) disponibles
para la herramienta giratoria sin cordón con objeto de
acomodar diferentes tamaños de cuerpo. Para instalar
un portaherramienta distinto, saque la tuerca del porta-
herramienta y quite el portaherramienta viejo. Introduzca
el extremo no ranurado del portaherramienta en el
agujero que se encuentra al final del eje de la herra-
mienta. Vuelva a colocar la tuerca del portaherramienta
en el eje.
Utilice siempre el portaherramienta que
corresponda al tamaño del cuerpo del accesorio que
usted piensa utilizar. Nunca intente introducir a la
fuerza en un portaherramienta un cuerpo de diámetro
más grande que el que pueda aceptar dicho
portaherramienta.
Para cambiar los accesorios, apague la herramienta,
deslice el botón del cierre del eje hacia la punta de la
herramienta y gire la tuerca del portaherramienta en
sentido contrario al de las agujas del reloj (aproximadamente
tres vueltas). Cambie accesorios introduciendo el nuevo
accesorio en el portaherramienta hasta donde se pueda
para minimizar el descentramiento y el desequilibrio.
Con el cierre del eje acoplado, apriete la tuerca del
portaherramienta con los dedos hasta que el
portaherramienta agarre el cuerpo del accesorio. Evite
apretar excesivamente la tuerca del portaherramienta.
EQUILIBRADO DE ACCESORIOS — Para realizar trabajo
de precisión es importante que todos los accesorios se
encuentren bien equilibrados (de manera muy parecida
a las gomas de su automóvil). Para nivelar o equilibrar
un accesorio, afloje ligeramente la tuerca del
portaherramienta y haga girar el accesorio o el
portaherramienta 1/4 de vuelta. Vuelva a apretar la
tuerca del portaherramienta y ponga en marcha la
herramienta giratoria sin cordón. El sonido y la
sensación del accesorio deberán permitirle saber si éste
está funcionando de manera equilibrada. Siga realizando
ajustes de esta manera hasta lograr el mejor equilibrio.
Para mantener equilibradas las fresas abrasivas, antes
de cada utilización, con la fresa fijada de manera segura
en el portaherramienta, encienda la Stylus y pase la
piedra de reacondicionamiento 415 ligeramente contra
la fresa que gira. Esto quita las partes que sobresalen y
nivela la fresa para que ésta quede bien equilibrada.
Ensamblaje
CUADRO DE IDENTIFICACION DE PORTAHERRA-
MIENTAS Los tamaños de portaherramienta se
pueden identificar por medio de las anillas que se
encuentran en el extremo posterior del portaher-
ramienta.
El portaherramienta de 0,8 mm tiene (1) anilla.
El portaherramienta de 1,6 mm tiene (2) anillas.
El portaherramienta de 2,4 mm tiene (3) anillas.
El portaherramienta de 3,2 mm no tiene anillas.
Inserción y remoción de accesorios
ASEGURESE SIEMPRE DE QUE
LA HERRAMIENTA ESTE EN LA
POSICION “APAGADO” ANTES DE CAMBIAR
ACCESORIOS, CAMBIAR PORTAHERRAMIENTAS O
REALIZAR SERVICIO DE AJUSTES Y REPARACIONES
DE LA HERRAMIENTA GIRATORIA SIN CORDON.
ADVERTENCIA
!
PRECAUCION
!
Instrucciones de funcionamiento
Introducción
Gracias por comprar la Dremel Stylus. Esta herramienta
fue diseñada para brindarle la máxima precisión y el
máximo control cuando trabaje en sus proyectos. La
carcasa ergonómica está diseñada para que usted
agarre y controle esta herramienta como si fuera un
lápiz, entre el dedo pulgar y el dedo índice. Cuando la
sostenga en esta posición (vea la página 55), ¡apenas
podrá sentir la herramienta liviana y compacta en la
mano! La herramienta está diseñada para ser
simplemente una extensión de la mano.
BOTON DE
FIJACION
DEL EJE
PARA
AFLOJAR
PARA
APRETAR
TUERCA DEL
PORTA-
HERRAMIENTA
PORTA-
HERRAMIENTA
LLAVE DE
PORTAHERRAMIENTA
DREME
D
R
EME
TUERCA DEL
PORTAHERRAMIENTA
ANILLAS DE
IDENTIFICACION
PORTA-
HERRAMIENTA
480 DE 3,2 mm
PORTAHERRAMIENTA
481 DE 2,4 mm
PORTAHERRAMIENTA
482 DE 1,6 mm
PORTAHERRAMIENTA
483 DE 0,8 mm
DM 2610930085 11-05 11/30/05 2:57 PM Page 52
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 1100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 1100 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info