768192
32
Zoom out
Zoom in
Previous page
1/44
Next page
R699870 - Helios User Manual
FUNCTION
32
Language
Choose the OSD language between: English, Japanese, German, Spanish, Italian, French, Portuguese, Dutch,
Swedish, Norwegian, Russian and Chinese.
12.0 FUNCTION
12.1  Trigger
The 12V trigger output can be used to control any compatible devices such as motorized screens or anamorphic
kits: The 12V trigger output is 12Vcc, 100mA. Select the trigger output behavior:
Off: 12V trigger voltage state is always low.
Power: 12V trigger state is high when the projector is powered ON. To be used with motorized screens.
Anamo: 12V trigger is high only when Anamorphic Mode A or Mode B is engaged. To be used with motorized
anamorphic kits.
Inst. Mode 1 up to 10: 12V trigger state is high when the selected Installation Mode is the same as the Mode
number congured.
12.2  O󰀨-Timer
You can congure this automatic power Off function that will switch off the projector when there is no operation
or after a determined timer. Choose the duration of the timer between: Off, 1 hour, 2 hours, 3 hours and 4 hours.
12.3  ECO Mode
This setting when set to On will minimizes the power consumption in the Standby Mode. Additionally, it will
automatically switch Off whenever the input signal is interrupted for 20 min. Must be Off to operate this unit from
Standby Mode with RS-232, LAN communications or Control4 protocols.
12.4  Network
When the Communication Terminal selected is LAN, this unit will be visible on the local Network and the following
parameters need to be congured. Refer to next section for more info.
12.5  Remote Code A or B
Select in the projector menu the code A or B according to the code selected on the RCU. You can change
the code used by the RCU to communicate with the projector from A to B. To do so, press and hold for 3 sec
simultaneously [MENU]+[BACK] buttons on the RCU. All the buttons on the RCU will blink.
Two blinks indicate that B code is used.
Three blinks indicate that A code is used.
12.6  Hide Mode
This setting is used to temporarily hide the current image by switching Off the Laser alimentation. You can also
use the [Hide] button on the RCU to set this function.
12.7  FactoryReset
Conrm to reset all this unit settings to default settings at once.
12.8  SoftwareUpdate
Conrm to start the update procedure. Make sure that a valid software le must be loaded on an USB stick and
that this stick is fully inserted in the USB/Update input located at the rear of this unit.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DreamVision Helios at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DreamVision Helios in the language / languages: English as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info