653174
2
Zoom out
Zoom in
Previous page
1/2
Next page
Battery Handling
Batteries, rechargeable or not, should not be disposed
of into ordinary household waste. Instead, they must be
recycled properly to protect the environment and cut down
the waste of precious resources.
Your local waste management authority can supply details
concerning the proper disposal of batteries.
In compliance with the EU Directive 2006/66/EC, the button
cell battery located on the printed circuit board inside the
product, can be removed at the end of the product life, by
professional personnel only.
Note: Settings
changes can be
made via the
MiTime unit
MiStat
Current room temperature
+hr key: Press to add up
to 3 hours to the current
period or to get instant
1 to 3 hours if currently
off (see step 8).
key: Press to
toggle between
Comfort setting, Eco
setting and Home
(Room thermostat
only). See table below.
key: Press to
cancel +hr and display
home. (Cylinder
thermostat only)
Select key: Press
to open and save
editor screens
Current Setting,
see table below
Current set temperature
Call for heat indication.
Thisame will be visible
when the room
temperature is below
the set temperature.
+ & - keys:
Press to change
the current
temperature or
turn the heat on
if currently off
RF transmission indication.
The RF symbol will be
visible as follows,
Short flashes indicates an
RF transmission.
Long flashes indicates an RF
transmission issue.
Symbol in
display
Function Description
Comfort setting
Selects the comfort setting. The pre-set value is used
each time when activated, adjustable within the menu
Eco setting
Selects the Eco setting. The pre-set value is used each
time when activated, adjustable within the menu.
None Home screen
Indicates that the pre-set temperatures were changed
via +/- key
Press Select to enter a specific
Setting. Options shown below:
Feature: Description: Factory Pre-Set:
Help Tips Describes the button functions
Holiday switch
off
In the period until holiday starts the product will operate normally.If holiday
is disabled manually or terminates automatically, the mode before start
of holiday will be re-instated.An enabled holiday will be indicated with a
suitcase symbol in the top line. If holiday is active, in the Set: line the holiday
end date will be indicated. In the Summary screen the suitcase will be visible
together with the holiday temperature.
Status Enable or disable holiday mode. Disabled
Zones Holiday mode can be applied to a specific zone or
all zones
All zones
Holiday start
time (From)
Set the time for the start of your holiday Current time -
nearest hour
Holiday start
date (From)
Set the date for the start of your holiday Today
Holiday end time
(To)
Set the time for the end of your holiday Current time -
nearest hour
Holiday end date
(To)
Set the date for the end of your holiday Today + 1 week
Time and date settings
Set time To set time of day Factory set
Set date To set date Factory set
Daylight saving To enable or disable daylight saving Enabled
Clock format To select 12h or 24h clock mode 12hr
Feature: Description: Factory Pre-Set:
Programme
Timetable
On & Off times for the current period can be
modified. See description in ‘Step 4’
Copy days Will copy the current day to one or more other days
Add Period Adds a Time event. It will be added at the correct
position within the day. There is a maximum of 4
periods.
Remove Period Removes the selected period. There needs to be at
least 1 period
Change
Timetable Type
The visible day-blocks available in "programme
timetable" can be defined, see Step 4
Individual days Each day can be programmed individually
Week and
weekend
Mon… Fri and Sat… Sun can be programmed as 2
blocks
Default
All week Mon…Sun can be programmed as one block
Stored
programmes
MiTime contains 3 pre-set programmes. These
programmes can be modified according to personal
needs and can be stored by using a name. Via this
name they can also be re-loaded. Once a programme
has been modified, the original factory pre-set will no
longer be available unless a System Reset is applied -
see Installation Guide Step 4.
Programme 1
Load stored
programme
A pre-set programme can be loaded
Save current
programme
The current programme can be saved by name (Each
pre-set program includes: Individual days, week/
weekend, all day and custom day schedules)
Step 6: Additional User Settings
Step 7: Keys and Display - MiStat Step 8: +hr (Boost) Step 9: Changing the Batteries
RF Pack: MiStat N110R, MiStat C110C
How do I know when to change
the batteries?
When the batteries start to run low a battery icon will
flash in the display to indicate “low battery, during
this time the MiStat will function normally. When the
battery icon alone is alone is shown in the display, the
batteries are completely exhausted and the MiStat will
cease to function (see below). Re-activate by replacing
the batteries.
How to replace the batteries
Remove the battery covers as shown. Replace the batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery covers pressing fully home.
Battery Covers:
Slide outwards
to remove
MiStat Rear
MiStat
MiStat
MiStat
MiStat
MiStat
Troubleshooting:
Press +hr to Boost
MiStat
Press +/- to adjust +hr period between 0 and 3 hours
Press ( ) to confirm
Now the Boost is running. The time will be counted
down each hour.
Once the time has elapsed, control returns to the
prior temperature screen.
The Boost can be cancelled by pressing the (
) key
or by setting the +hr period to 0.
1 Setting temperature values is restricted
a
Are Minimum/Maximum temperatures activated?
see Installation Guide Step 8.
2
NO SIGNAL is visible on the screen, no reaction on
key presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
b
Is the room thermostat powered? see Homeowner
Guide Step 9.
3 LOCKED is displayed on the room themostat
a see Installation Guide Step 8 - Screen Lock
4 Is the battery symbol visible?
a Replace batteries, see Homeowner Guide Step 9.
5
STARTING is visible on the thermostat screen, no
reaction on key presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
6
WAIT is visible on the thermostat screen, no reaction
on key presses anymore
a
Is the receiver powered? (Red signal lamp should
be visible)
Step 5: Period Settings
Stored programmes
MiTime contains 3 pre-set programmes. An
example is shown below. These programmes can
be modified according to personal needs and
can be stored by using a name. Via this name they
also can be reloaded. Once a programme has
been modified, the original factory pre-set will no
longer be available. On a System Reset, only the
current loaded programme will be replaced with
the factory setting – see Installation Guide Step 4.
All week Week & Weekend
Mon-Sun Mon-Fri Sat-Sun
Programme 1
Example:
Step 4: Prog. Timetable
Zone = Heating
Help text: Use left/right buttons to
select the days you want to change
Period 1 settings: describes the current timetable
settings, e.g. Heating has been programmed to
turn On at 6:30am and go off at 8:30am
Period 2 settings: describes the current timetable
settings, e.g. Heating has been programmed to
turn On at 4:30pm and go off at 10:30pm
Press select (
) when highlighted to adjust
settings (see Step 5)
Up to 4 periods can be programmed
Arrow denotes that further options are
available if you scroll down.
Timetable day range: Monday to
Friday (Week and weekend)
Options: Individual days (7day), Week and
weekend (5/2day), All week (24hr). The
available blocks depend on the selection
in menu change timetable type
Link to Copy days
Day range & period
Help text: Use left/right buttons to
change fields
Period settings: On at 6:30am and Off
at 8:30am
Highlight shows adjustable field:
Use up/down buttons to adjust values
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Drayton MiTime T720M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Drayton MiTime T720M in the language / languages: English as an attachment in your email.

The manual is 2,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Drayton MiTime T720M

Drayton MiTime T720M Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info