680245

Draytek VigorSwitch P1280 Manual

16
Zoom out
Zoom in
Previous page
1/120
Next page
VigorSwitch P1280 User’s Guide
1
0
Media Speed Wiring
10 Mbps Category 3,4,5 UTP/STP
100Mbps Category 5 UTP/STP
10/100/1000
Mbps copper
1000 Mbps Category 5e, 6 UTP/STP
I
I
-
-
2
2
-
-
3
3
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
i
i
n
n
g
g
t
t
h
h
e
e
M
M
a
a
n
n
a
a
g
g
e
e
m
m
e
e
n
n
t
t
A
A
g
g
e
e
n
n
t
t
o
o
f
f
S
S
w
w
i
i
t
t
c
c
h
h
Users can monitor and configure the switch through the following procedures.
Configuring the Management Agent of VigorSwitch P1280 through the Ethernet Port.
There are several ways to configure and monitor the switch through Ethernet port, includes
Web-UI and SNMP.
I
I
-
-
2
2
-
-
4
4
M
M
a
a
n
n
a
a
g
g
i
i
n
n
g
g
V
V
i
i
g
g
o
o
r
r
S
S
w
w
i
i
t
t
c
c
h
h
P
P
1
1
2
2
8
8
0
0
t
t
h
h
r
r
o
o
u
u
g
g
h
h
E
E
t
t
h
h
e
e
r
r
n
n
e
e
t
t
P
P
o
o
r
r
t
t
Before start using the switch, the IP address setting of the switch should be done, then
perform the following steps:
1. Set up a physical path between the configured the switch and a PC by a qualified UTP Cat.
5e cable with RJ-45 connector.
Note: If PC directly connects to the switch, you have to setup the same subnet mask
between them. But, subnet mask may be different for the PC in the remote site. Please
refer to the above figure about the Web Smart Switch default IP address information.
2. After configuring correct IP address on your PC, open your web browser and access
switch's IP address.
Default system account is "admin", with password "admin" in default. Switch IP address is
"192.168.1.224" by default with DHCP client enabled.
I
I
-
-
2
2
-
-
5
5
I
I
P
P
A
A
d
d
d
d
r
r
e
e
s
s
s
s
A
A
s
s
s
s
i
i
g
g
n
n
m
m
e
e
n
n
t
t
For IP address configuration, there are three parameters needed to be filled in. They are IP
address, Subnet Mask, Default Gateway and DNS.
IP address:
The address of the network device in the network is used for internetworking communication.
Its address structure looks is shown below. It is “classful” because it is split into predefined
address classes or categories.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Draytek VigorSwitch P1280 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Draytek VigorSwitch P1280 in the language / languages: English as an attachment in your email.

The manual is 2,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info