680221

Draytek Vigor 2862 LTE Series Manual

973
Zoom out
Zoom in
Previous page
1/988
Next page
Vigor2862 Series User’s Guide
95
7
1: Active-Standby
0: Hot-Standby
-v <1-255> Specify the group ID (VHID)
1- 255: Setting range.
-R Set HA settings to Factory Default.
-p <1-30> Specify the Priority ID.
1-30: Setting range.
-k <key> Specify the Authentication Key.
Key: Max. 31 Characters.
-u <1/0> Enable or disable the function of Update DDNS.
1: Enable. When a router changes HA status to primary, it will
update DDNS automatically.
0: Disable.
-m <interface> Specify the management interface.
Interface: LAN1 ~ LAN6, DMZ.
-s It means to get the newest status of other router (except the local
router).
-y
It means sync local config to other router. Primary can executes this
command. Secondary can not execute this commad.
-c <1/0> Enable or disable the function of Config Sync.
1: Enable.
0: Disable.
-I -[M|H|D] <interval> Set the Config Sync Interval for HA. Minimum interval is 15 minutes.
-M: Minute. Setting range is 0/15/30/45. (e.g., ha set -I -M 30)
-H: Hour. Setting range is from 0 to 23. (e.g., ha set -I -H 12)
-D: Day. Setting range is from 0 to 30. (e.g., ha set -I -D 15)
-h -<4/6><Subnet> [<Virtual
IP>]
Enable and set virtual IP to the subnet.
4: IPv4; 6: IPv6.
Subnet: LAN1 to LAN6, DMZ.
Virtual IP: The type format shall be “xxx.xxx.xxx.xxx”. (e.g,
192.168.1.0)
For example, to enable a virtual IP to the sunet, simply type:
ha set –h LAN1 192.168.1.5
-d -<4/6><Subnet> Disable a virtual IP to the subnet.
4: IPv4; 6: IPv6.
Subnet: LAN1 to LAN6, DMZ.
For example, to disable a virtual IP to the subnet, just type:
ha set –h LAN1
-o <1/0> Run DARP protocol on IPv4 or IPv6.
0: IPv4
1: IPv6
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> > ha set -h -4 LAN1 192.168.1.1
% Enable IPv4 Virtual IP on LAN1
% Virtual IP can not be same as router IP (192.168.1.1)!!!
>
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
h
h
a
a
s
s
h
h
o
o
w
w
This command can be used to show the settings information about config sync and general
setup.
… 973 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Draytek Vigor 2862 LTE Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Draytek Vigor 2862 LTE Series in the language / languages: English as an attachment in your email.

The manual is 15,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info