499409
34
Zoom out
Zoom in
Previous page
1/35
Next page
Cleaning of the unit and of the acrylic sheets
Use a damp cloth to clean the unit. The acrylic sheets
should be cleaned at regular intervals. Use only sol-
vent-free, non-corrosive agents without artificial
aroma.
If you want to take out the acrylic sheet, grasp it at the
side of the profile and pull it frontward. Then grasp it
from behind, as shown in fig. 43, and bend it slightly
inwards. Now you can push the sheet out of the late-
ral guiding, proceeding from top to bottom. In this way
you are able to clean the sheet from both sides.
When the sheets are cleaned, put them in again. Fig. 43
profile
acrylic sheet
Maintenance
Replacement of UV-lamps and starters
To replace lamps and starters first remove the acrylic
sheets following the procedure described above.
Depending on the total number of operation hours,
the lamps of your unit must be replaced at certain
intervals.
Fan delay
For cooling purposes, it is alwasy necessary that the
fans run an additional 3 minutes or more after every
use. This extra time period is part of the control
programming and cannot be shortened.
This time period can be lenghtened by the coin box or
the external timer. This can be useful when
encountering temperature problems due to an
inadequate or excessive ventilation situation.
Decorative lighting
After the tanning lamps have been switched off by the
coin box or the external timer, the decorative lighting
is switched on automatically. It can be switched off with
the switch seen on fig. 42a.
contact pins
The lifespan of UVA low-pressure lamps is
approximately 500 hours. When replacing them make
sure to use only original spare parts. When ordering
these parts from your customer service or retailer
always state the number of the unit (nameplate). Please
remember that this is the general procedure when
ordering any spare parts.
To remove or insert UV low-pressure lamps turn them
by 90 degrees in their top and bottom holders and
take them out frontward. When inserting new lamps
make sure that the contact pins at the end of the lamps
is properly located in the holders.
The starters are positioned at the upper or lower ends
of the lamps (depending on equipment version). They
are removed or inserted by 90 degree rotation. Fig. 44.
Fig. 44
UV lamp
starter
34 english
Fig. 42a
switch for
decorative lighting
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dr. Kern Tandome at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dr. Kern Tandome in the language / languages: English, German as an attachment in your email.

The manual is 0,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info