Manual Dr. Kern excellent 28 9 (page 20 of 28) (English, German)

499399

Zoom out

Zoom in

1/28

english

In preparation for the assembly of the canopy, first push

the fitted side panels outward slightly at the upper end.

Insert a screwdriver or similar tool into the gap to hold the

side panels in this position, see Fig. 19.

Mouthlike groove

Protection Plate

Attachment screw for

protection plate

Fig. 19

Do not remove

this screw

With the aid of a second person, now lift the canopy out of

the packaging, and hold it above the bench so that both

bearing bushes with the groove can slide into the mouth-

shaped opening, see Fig. 21.

Ball-joint

connector

Gas Spring

Safety washer

Ball-joint

connector

Installation-

groove

Fig. 23

Cotter pin-holes

Gas Pressure Spring Installation

Safety rings have been clipped into the upper end of

the gas pressure springs (which are already firmly

mounted on the safety bracket) - on the ball socket.

These rings must be removed as schown in Fig. 23

In order to fasten the gas pressure springs on the top,

the top must be lifted upward as far as possible until

the ball socket on the gas pressure spring is directly

aligned with the ball pin.

Applying moderate to strong pressure, press the ball

socket onto the ball pin.

NOTE! The ball-joint connectors have been

lubricated at the factory with a special grease, which

may not be removed.

Fig. 22

Screw in solidly

Rotating housing

Protection

plate

After the canopy has been properly and securely

mounted, it can be lowered gently onto the bench.

Replace the side cover panels in the manner in which

they were delivered.

Two people may now lift the canopy out of its wrap-

ping and place both ends so that they can slide into

the groove with the mouthlike opening. See fig. 21.

With one person holding the canopy securely at the

front, secure the canopy into the rotating housings. To

this you must first place both protection-plates so that

the big opening on the protection-plate grasps over

rotating housings. See fig. 22.

After you have placed both protection-plates at the left

and right rotating housings, secure their respective

securing screws with the enclosed SW 10 wrench.

Securing screw for

protection plate

Protection plate

Side cover

Rotating housings

Fig.21

Assembly and Mounting of the Canopy

The last setup step on the bench is the loosening of

the right and left side panels, which will cause the

securing panels to become free. These protection-

plates cover the openings into which the canopy (with

its rotating housings at either end), will be placed.

Loosen the securing screws on the protection plates

so that they can be turned away from the opening in

the canopy to free them for mounting. See fig. 20.

Mouthlike groove

Protection Plate

Securing screw to

Canopy Chassis

Fig.20

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dr. Kern excellent 28 9 in the language / languages: English, German as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dr. Kern excellent 28 9 Manual

Product: