368842

Dr. Kern excellent 24 1 Manual

19
Zoom out
Zoom in
Previous page
1/28
Next page
19
english
Fig. 13
You will now see 3 openings at each head side on the
rear wall of the bench. Now insert the foot panel with the
projecting flaps into the slot between the rear wall and
head strut, and then press the foot panel firmly onto the
rear wall.
Now attach the foot panel to the head strut using 3 screws,
4.2 x 9.5, from the accessory bag, see Fig. 13. Fit the se-
cond foot panel at the other head side in the same way.
Fit foot panel using 3 screws
Looking from the front side, you will see almost at the
upper end of each foot an attachment hole. Fit the floor
rail into these holes using 2 screws, 4.2 x 9.5, as shown
in Fig. 14.
Fig. 14
Fitting screw, 4.2 x 9.5
Slot in floor rail
Foot panel
The floor rail should be pushed up as far as possible.
Note also that the lateral slots in the floor rail should project
into the side wall of the foot panel, thereby ensuring the
correct lateral distance of the foot panels.
Fig. 15
Foot panel
Floor panel
Lower groove in
lengthwise spar
Upper groove in
floor rail
To complete the assembly of the bench, now fit the front
foot panel between the other two foot panels. To do this,
first insert the long side, with the small recesses visible at
the left and right, into the lower groove in the lengthwise
spar.
Now push the panel as far as possible into this groove.
The panel must be clipped into the upper groove of the
floor rail. To do this, first bend the panel outward slightly at
one end, as shown in Fig. 16, and then push the upper
end of the panel into the upper groove in the floor rail.
Fig. 16
Bend the panel
outward slightly
here, and clip into
the upper groove.
Repeat this bending and pushing process at several points
until the panel has been inserted fully into the groove.
This completes the foot and pedestal assembly. The bench
can now be placed in the required position on its feet (Fig.
17).
Fig. 17
The side panels of the bench can now be screwed back
into place. The two upper attachment screws at each side
should not be tightened yet.
Fig. 18
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dr. Kern excellent 24 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dr. Kern excellent 24 1 in the language / languages: English, German as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info