Manual Dovre VISTA 600 (page 52 of 261) (English, German, Dutch, French, Italian, Spanish, Norwegian)

813293

Zoom out

Zoom in

1/261

16 Subject to change because of technical improvements

Prepare

connection to outside air

If the appliance is installed in a room with insufficient

ventilation, you can install the outside air connecting

kit to the appliance.

09-20021-130

The outside air collar can be assembled on the outside

depending on how the fireplace is built in, see position

2 in the figure above. If the method of building in and

the connection of the outside air requires the outside

air collar to be assembled through the inside, first

remove the inner plates and the fire compartment

base. Then remove the air distribution housing, see

position 1 in the figure above. Disassemble the con-

necting collar for the outside air, connect it airtight to

the flexible hose for the outside air, assemble the con-

necting collar through the inside of the appliance and

assemble the air distribution housing.

Make sure that the seals are not damaged. If

they are damaged the seals must be replaced.

Make sure that the air distribution housing is

connected airtight and that the working of the

air slide valve is not impeded.

The air supply tube is 100mm in diameter. If the tube

is smooth, it may be no longer than 12metres. If

accessories such as bends are used, the maximum

length (12m) must be reduced by 1m for each access-

ory used.

Outside air intake duct through the

wall or the floor and the connection

collar

1. Make a hole in the wall or the floor (refer to

Appendix 2, "Dimensions" for a suitable position

of the hole).

2. Close the air connection tubehermetically on the

wall.

Building into a new hearth

The fireplace insert is installed in two stages:

Placing and connecting the fireplace

Building up the hearth around the fireplace.

Placing and connecting the fire-

place insert

1. Place the appliance at the right height, flat and

level.

2. Make sure there is sufficient space between the

existing walls (insulated as per instructions) and

the rear of the appliance.

3. Connect the appliance to the flue hermetically.

4. Check the draught in the flue and the seal of the

connection on the flue gas duct by making a small,

intense trial fire with newspaper and dry, small

kindling.

Wait until new masonry has dried sufficiently.

5. For outside air supply connection: connect the out-

side air supply to the connection kit you fitted to

the appliance.

Building the fireplace

Inside the hearth you provide space for convection. In

this space the air must be able to move freely. It must

be possible for air to be drawn in for combustion pur-

poses, and the air heated by the built-in fireplace (the

convection air) must be able to flow freely within the

space to be heated; see following figure.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dovre VISTA 600 in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 8.88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dovre VISTA 600 Manual

Product: