Manual Dovre Sense 100 (page 46 of 180) (English, German, Dutch, French, Italian, Spanish)

571208

Zoom out

Zoom in

1/180

Lubrication

Although cast-iron is slightly self-lubricating, you will

still need to lubricate moving parts frequently.

Lubricate the moving parts (such as guide sys-

tems,hinge pins, latches and air slides) with heat

resistant grease that is available in the specialist

trade.

Touching up damaged paint

Small areas of damaged paint finish can be touched-

up with a spray can of special heat-resistant paint,

available from your supplier.

Touching up the enamelled surface

Enamelling is a process carried out by traditional meth-

ods, meaning that it is possible that small colour dif-

ferences and damage may occur. The appliances

undergo a visual inspection in the factory, that is to

say, the inspector looks at the surface for a period of

10 seconds from a distance of 1 metre.

Any damage that does not stand out is regarded as

OK. A special heat-resistant paint is supplied with the

stove to touch up any minor damage caused during

transport.

Apply the heat-resistant paint in thin layers and leave

to dry well before using the appliance.

Some enamel colours are temperature-sensitive. It

can happen that the colour changes during use.

The original colour will return when the stove has

cooled down.

If enamelled surfaces become very hot, hairline

cracks can occur. This is a normal phenomenon

and has no impact on the functioning of the stove.

Ensure that the stove is not overburdened. If it

does become overburdened then the surface

gets very hot possibly resulting in lasting dam-

age to the enamel.

Checking the seal

Check whether the door sealing rope is still in good

condition and works well. The sealing rope is sub-

ject to wear and will need to be replaced over time.

Check the appliance for air leaks. Close any

chinks with stove sealant.

Allow the sealant to harden fully before lighting

the stove, as any moisture in the sealant will

form bubbles, resulting in a new air leak.

Adjust door closing

Check if the door closes properly. If required, the clos-

ing of the door can be set looser or tighter by adjusting

the distance between the locking cam and the door.

Proceed as follows:

1. Open the door. The locking cam (2) is now freely

accessible; see next figure.

2. Unscrew the two screws (1) with which the lock-

ing cam is attached.

3. By removing the packing plate (3) behind the lock-

ing cam (2), the door closes more tightly. If the

door closes too tightly then insert an additional

packing plate behind the locking cam.

4. Tighten the two screws and check the closing of

the door once again.

09-20021-024

123

Replacing the glass

If the glass in the appliance is broken or

cracked, it must be replaced before the stove

is used again.

In order to replace the side glass, all the inner panels

and the air guide must first be removed. The air guide

is attached with a M8 nut in the middle at the top of the

appliance. Proceed as follows:

Subject to change because of technical improvements

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dovre Sense 100 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 14,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dovre Sense 100 Manual

Product: