477733
7
Zoom out
Zoom in
Previous page
1/40
Next page
English
4
The display shows FLASH. Press
Q
to change or press
}
to continue without changes.
Select the desired setting using
{
/
}
. 100 for AU/UK/EU, 270 for FR and 600 for NZ.
Press
Q
.
The display shows TONE/PULSE. Press
Q
to change or pressor press press
}
to continue without
changes.
Select TONE or PULSE using
{
/
}
. If unsure about which mode to use, select TONE as
this works in most locations. Press
Q
.
The display shows ANSWER DELAY. Press
Q
to change or pressor press press
}
to continue without
changes.
Select 2, 4 or TS using
{
/
}
. Press
Q
.
The display shows ANSWER MODE. Press
Q
to change or pressor press press
}
to continue without
changes.
Select ANSWER&RECORD or ANSWER ONLY using
{
/
}
. Press
Q
.
The display shows PIN CODE. Press
Q
to change or pressor press press
}
to continue without
changes.
Use the numeric keypad to enter the default code (0000). Pressenter the default code (0000). PressPress
Q
. Enter the new code.
Press
Q
.
If the code is not accepted/correct you will hear a short beep, repeat step 21 and 22.
The display shows PRIVACY MODE. Press
Q
to change or pressor press press
}
to continue without
changes.
Select ON or OFF using
{
/
}
. Press
Q
.
The LCD shows “TOTAL:00 NEW:00”, which means both the total call and new call counter
are zero.
Press
w
anytime to change the settings. Press
1
/
to return to standby.
Number of Rings (Answer delay)
The number of rings before the answer machine answers can be selected between 2, 4
or TS.
With TS (Time Saver) selected, calls will be answered after four rings until a new ICM
(incoming message) has been recorded, any subsequent calls will be answered after two rings.
Once these ICM’s (incoming messages) have been erased this cycle will be repeated. This
is useful when remotely accessing your unit, if there is no answer after three rings no ICM’s
(incoming messages) have been recorded, you can therefore terminate the call before you are
charged.
Pin Code
This code is needed in order to gain access to the remote control functions of the answer
machine (factory setting is 0000). The same code is used for Privacy mode. You can alter the
code according to the description above.
Voice
With VOICE set to ON you will be announced the time for when the incoming message (ICM)
was recorded. With VOICE set to OFF the time and date will not be announced but you can
still see when the incoming message was recorded in the display.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Doro 916i cr at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Doro 916i cr in the language / languages: English, French as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info