784272
6
Zoom out
Zoom in
Previous page
1/28
Next page
6
NOTES ON NETWORK CONNECTION
You can connect the device to the network using
a network cable. The connection via WiFi is not
possible!
Install a network cable (which is plugged into
a network switch / router with Internet access)
from the inside of your building to the assembly
location. The network cable between the assembly
location and the network switch / router can have
a maximum length of 80 m/262 ft (IEEE 802.3).
If you must span a distance of more than 80
meters/262 feet you can put a network switch in
between. Make sure to use a high-quality Cat.5
network cable or better and with proper shielding
(Screened Foiled Twisted
Pair (S/FTP or SFTP)) whereby the shield is
connected to the outer metal
shield of the RJ45 plug (8P8C).
If you have only two wires available at
the assembly location, you may use the
“DoorBird 2-Wire Ethernet PoE Converter
A1071”, sold separately. It allows you to
transfer network data (Ethernet) and
power (PoE) with a simple two-wire
cable over long distances. For example,
existing buildings with a simple two-wire
bell wire can be equipped with network
technology without having to retrofit any
network cables.
Network speed and network components
Please ensure that the upload speed of your Internet
connection is at least 0.5 Mbps. The user experience is
only as good as your network speed, network stability
and quality of your network components, such as
your Internet Router and WiFi access points or WiFi
repeaters. Please also make sure that your network
components are no older than two years old, have
been manufactured by a well-known manufacturer,
and have the latest firmware installed.
Should these requirements not be fulfilled, it may
occur, for example that the performance of audio and
video is poor or push notifications are delayed or do
not arrive on your smartphone or tablet at all.
Requirements:
High-speed Internet (via landline): DSL, cable or
optical fibre
Network: Ethernet, with DHCP
SWITCHING OFF POWER
Switch off the power to all wires leading to
the assembly location, i.e. the door chime,
electric door opener, power supply unit for
the video door station etc.
REMOVAL OF THE EXISTING
FRONT PANEL
Turn the safety screws counterclockwise until they
loosen.
Disconnect all cables from the main unit of your D202
or D201. Carefully remove the D201/D202 front panel
with the main unit from the mounting housing.
CONNECTING THE DEVICE
You can connect all necessary cables and wires to the
device now.
For easier installation we strongly
recommend to remove the plug from screw
connection terminal while you connect the
cables and wires.
NOTICE Please remove any cables and wires from the
connection ports of the device that you do
not need.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Doorbird D1101UV - IP Video Door Station at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Doorbird D1101UV - IP Video Door Station in the language / languages: English, German as an attachment in your email.

The manual is 2.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info