784488
11
Zoom out
Zoom in
Previous page
1/52
Next page
1111
ENGLISHENGLISH
Option 1: Power supply using the power-supply unit (mains adaptor)
Two insulated wires are required to power the device by connecting it to the
power-supply unit (mains adaptor) supplied with it. These wires are normally
already there and are freely accessible once you have removed the previous
door chime. You can also connect the power supply without any additional
wires to the door chime, the power supply has a 300cm long cable with two
insulated wires. If you need longer wiring, connect the wires of the power
supply using the supplied crimp connectors with the two wires that you want
to use for the power supply.
Do not plug the power supply unit into the wall socket yet.
Only use the power supply unit provided along with the device, or a
DIN-rail power supply unit that you can obtain from us separately,
since this has been specially stabilized electrically and is equipped
with an integrated audio interference reduction device. Other power
supply units may destroy the device or cause poor transmission quality.
The warranty automatically expires if you use a different power supply
unit. The power supply unit is plugged into a wall socket inside your
house, usually where the two wires from your previous door chime
comes out of the wall in the interior of the house.
Option 2: Power supply via PoE (as an alternative)
To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector
(e.g. DoorBird Gigabit PoE Injector) in accordance with the PoE standard IEEE
802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a Cat.5
cable or better are to be used. A Cat.5 cable or better must be used as network
signals can only be transmitted over completely insulated, shielded and
twisted cables. If you use PoE as a source of power, the WiFi interface of the
device is automatically inactive, and the four wires for PoE then simultaneously
form the data link. The device won’t start if your PoE Switch or PoE injector
does not support the PoE Standard IEEE 802.3af Mode A (see Diagnostic-LED
and Diagnostic-Sounds).
1. Disconnect the PoE-Switch or PoE-Injector from the power grid.
2. Place the network cable in the installation site of the device.
Do not combine the power supply from the power supply unit
(mains adaptor) with the power supply via PoE. You can find further
information about PoE here: http://www.doorbird.com/poe
STEP : FURTHER CONNECTIONS (OPTIONAL)
If desired, connect additional wires to the installation site of the device.
The wires or connection options mentioned in this section are optional.
NOTICE
NOTICE
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Doorbird A1061x Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Doorbird A1061x Series in the language / languages: English, German, French as an attachment in your email.

The manual is 0.48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info