773928
27
Zoom out
Zoom in
Previous page
1/60
Next page
27
DO7347H
www.domo-elektro.be
EN
USE
Before you use the appliance: plug in the appliance and turn on the on/o switch at the back of the device.
The display displays the symbol and emits an audible signal to indicate that the device is in standby
mode. You can set the appliance using the control panel, but also using the remote control. You can make
the settings in the same way. The display will show you the selected settings. Each time a button is
pressed, the device emits an audible signal to indicate that the user is making a setting or adjustment.
ON/OFF SWITCH
Push the on/o switch to turn on or o the appliance. “HI” and the symbol appear on the display when
the device is switched on. This means the device is at its highest power setting. If you switch o the
device, the display will count down from 15 to 0 in order to cool itself down.
Note: when the device is switched o via this button, the device goes into standby mode. This means it is
not completely disabled. You can only switch the device o completely via the on/o switch on the back
of the device.
FUNCTION BUTTON
1. Press the button once: low power (1200 W): “LO” appears on the display, the device is now operating
at its lowest power setting.
2. Press the button a second time: ECO: the symbol appears on the display. You can set the
temperature between 5-35 °C as desired using the buttons to increase and to decrease . You
can also keep this button pressed until you reach the desired setting. If the ambient temperature is 2
°C higher than the set temperature, the device switches to standby mode. If the temperature falls
back below the set temperature, the eco function switches on again. This is the most energy-
ecient way to maintain the temperature.
Note: the device remembers the last temperature setting made. This means that when you switch
the device on again, the last temperature setting appears on the display when eco mode has been
selected.
3. Press the button for a third time: high power (2000 W): “HI” appears on the display, the device is
now operating at its highest power setting.
TIMER
1. Push this button to set the timer. The symbol appears on the display.
2. You can set this between 1-8 hours using the buttons to increase and to decrease . You can
also press and hold this button until you reach the desired setting.
3. When the selected time has been expired, the appliance will enter the stand-by mode and will no
longer emit heat.
Note: if the device is in stand-by mode, you can set the timer. After the set time has elapsed, the device
switches itself on automatically and will operate at its highest power setting.
OSCILLATION
Press the oscillation button to allow the heater to oscillate the air from left to right and vice versa. Press
this button again to stop this. If you switch the device o with the on/o button, this function stops even
if you have not pressed the oscillation button.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Domo DO7347H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Domo DO7347H in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info