629513
6
Zoom out
Zoom in
Previous page
1/24
Next page
Mounting the Display Elite Control Operations Manual
4 L-2230 ENGLISH
MOUNTING THE DISPLAY
1. Make the cut-out for the display panel. Cut-out size is 3-5/16” (8.41cm) wide by 2-3/16” (5.56cm) high.
2. Plug one end of the display cable (8-pin connector) into the upper-right socket on the circuit board in the electric box
and the other end into the back of the display panel.
3. Secure the display panel to the bulkhead using the four screws provided. Do not use a screw gun and do not over-
tighten screws when mounting, because either method may damage the display.
4. When the display is securely mounted, mount the bezel over the display frame until it snaps into place.
MOUNTING THE OPTIONAL SENSORS
REMOTE AIR SENSOR
Install the optional remote air sensor if the display can not be mounted in a proper location for accurately sensing room
temperature. Installing the remote air sensor overrides the display’s built-in sensor. The standard cable length for the remote air
sensor is 7 feet (2.1m).
1. Mount the remote air sensor in the return-air stream behind the opening of the return-air grille.
2. Plug its cable (6-pin connector) into the “ALT AIR” socket #J4 in the upper-left corner of the circuit board.
OUTSIDE AIR TEMPERATURE SENSOR
Install the optional outside air temperature sensor to monitor the temperature outside the cabin. Outside air sensor cables are
available in various lengths.
1. Mount the sensor outside but not in direct sunlight.
2. Plug its cable into the “OAT” socket #J3.
SERVICE SENSOR
Install the optional condenser coil temperature sensor into the “SERVICE/H2O” socket #J5. Use of this sensor must be enabled
via program parameter P-8, the Pump Sentry feature. See “P-8: Optional Pump Sentry” on page 9 for details.
OPERATION
OPERATOR CONTROLS AND DISPLAY PANEL
Refer to Figure 1, page 2 for the button locations and display functions listed below.
DISPLAY INDICATORS
Auto Mode Indicator - The Auto Mode LED lights when the system is in Automatic Mode, which switches to cooling or
heating as required to satisfy the temperature set point.
Cool Mode Indicator - The Cool Mode LED lights when the cool-only mode is selected or when the unit is in an
Automatic Mode cooling cycle.
Heat Mode Indicator - The Heat Mode LED lights when the heat-only mode is selected or when the unit is in an
Automatic Mode heating cycle.
Moisture Mode Indicator - The Moisture Mode LED lights when the Moisture Mode is selected. This mode controls
humidity during periods when the vessel is unoccupied.
IMPORTANT
The system’s air sensor is located in the control’s display panel, therefore the display MUST be located on an interior
wall at eye level. It must NOT be located in direct sunlight or inside a cabinet.
If these conditions cannot be met, you must purchase the Optional Remote Air Sensor and install it in the return-air
stream.
NOTE
Do not staple any sensor cables when mounting.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dometic Elite Control DX systems at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dometic Elite Control DX systems in the language / languages: English as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info