507618
15
Zoom out
Zoom in
Previous page
1/26
Next page
15
Die Modelle PS-342 und PS-344 sind mit der DOLMAR
Start&Go Startvorrichtung ausgestattet. Das Modell PS-344
ist darüberhinaus mit einem halbautomatischen Startventil
(C/2) zur Starterleichterung ausgerüstet.
Durch Hineindrücken des Startventils wird die Verdichtungs-
arbeit verringert, so dass der Motor schon mit geringem
Kraftaufwand am Anwerfseil auf seine Startdrehzahl beschleunigt
wird. Durch den hohen Druckanstieg im Brennraum, infolge der
ersten Zündungen, wird das Startventil automatisch geschlossen
(Knopf springt heraus).
Die Startvorrichtung Start&Go unterscheidet sich
wesentlich von üblichen Systemen. Das Starten der
Motorsäge wird durch Start&Go einfacher und ist leicht
nachzuvollziehen. Bitte folgen Sie den Anweisungen zum
Starten wie unter Kaltstart und Warmstart beschrieben.
Die zum Starten erforderlichen Schritte sind auf der
Abdeckhaube durch Symbole (A/1) dargestellt. Der blaue
Pfad ist für den Kaltstart, der rote Pfad für den Warmstart.
B
1
2
Starten der Motorsäge PS-342, PS-344
(PS-344)
2
Kaltstart (blauer Pfad A/1):
- Start/Stop Schalter (C/1) der Zündung in Position I.
- Startventil (C/2) (nur bei PS-344) hineindrücken.
- Kunststoffball der Primerpumpe (C/3) drücken, bis Kraftstoff
sichtbar.
- Starthebel (C/4) nach oben auf Position 1
- Anwerfseil langsam bis zum spürbaren Widerstand
herausziehen (der Kolben steht vor dem oberen Totpunkt).
- Jetzt schnell und kräftig weiterziehen. Der Motor springt
nach 2-4maligen Anziehen an (bei niedrigen Temperaturen
häufiger) und läuft durch.
Achtung:
Anwerfseil nicht mehr als ca. 50 cm herausziehen und nur
langsam von Hand zurückführen. Für ein gutes Startverhalten
ist es wichtig, das Anwerfseil schnell und kräftig zu ziehen.
- Sobald der Motor rund läuft, Gashebel (C/5) leicht antippen,
damit der Starthebel in die Nullstellung zurückspringt und
der Motor im Leerlauf läuft.
Achtung:
Der Motor muss nach Anlauf sofort in Leerlauf gebracht
werden, da sonst Schäden an der Kettenbremse eintreten
können.
- Jetzt Kettenbremse lösen.
Warmstart (roter Pfad A/1):
- Wie unter Kaltstart beschrieben, jedoch ohne Betätigung
der Primerpumpe (C/3) und den Starthebel (C/4) in Position
2 stellen.
Wichtiger Hinweis (roter dünner Pfad):
- Falls der Kraftstofftank völlig leergefahren wurde und der
Motor mangels Kraftstoff zum Stillstand gekommen ist,
nach dem Auftanken Starthebel (C/4) in Position 1 stellen.
Motor ausschalten
- Kurzschlussschalter (C/1) in Position O (STOP) bringen.
C
1
4
- Mindestens 3 Meter vom Tankplatz entfernen.
- Sicheren Stand einnehmen und Motorsäge so auf den
Boden stellen, dass die Sägevorrichtung frei steht.
- Kettenbremse auslösen (blockieren).
-Bügelgriff fest mit einer Hand umfassen und Motorsäge
auf den Boden drücken.
- Die rechte Fußspitze in den hinteren Handschutz stellen.
3
5
A
= Warmstart (rot)
= Start/Stop Schalter
= Primerpumpe
= Kaltstart (blau)
1
Motor starten (PS-342, PS-344 mit Start&Go)
= Starthebel
STOP
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PS-400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PS-400 in the language / languages: German as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar PS-400

Dolmar PS-400 User Manual - English, French - 64 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info