507616
24
Zoom out
Zoom in
Previous page
1/64
Next page
24
Checking the chain lubrication
E
Never work with the chain saw withoute sufficient chain
lubrication. Otherwise the service life of the chain and guide
bar will be reduced.
Before starting work check the oil level in the tank and the oil
feed.
Check the oil feed rate as described below:
- Start the chain saw.
- Hold the running chain saw approx. 15 cm above a trunk
or the ground (use an appropriate base).
If the lubrication is sufficient, you will see a light oil trace
because oil will be flung off the sawing device. Pay attention to
the direction the wind is blowing and avoid unnecessary
exposure to the oil spray!
D
6
Checking the chain brake
Do not work with the chain saw without first checking
the chain brake!
- Start the engine as described (make sure you have a good
footing, and place the chain saw on the ground in such a
way that the guide bar is free of contact).
- Grasp the tubular handle firmly with one hand and hold the
grip with the other.
- With the engine running at moderate speed, press the hand
guard (D/6) in the direction of the arrow with the back of
your hand until the chain brake engages. The chain should
stop immediately.
- Immediately release the throttle and release the chain
brake.
Caution: If the chain does not stop immediately in this
test, turn off the engine immediately. Do NOT use the
chain saw in this condition! Contact a DOLMAR service
center.
Adjusting the carburetor
IMPORTANT: Carburetor adjustment may be done only by
a DOLMAR service center!
Do not undertake adjustments to the adjusting screws (H)
and (L) without a tachometer! Improper adjustment can
lead to engine damage!
The adjusting screws (H) and (L) are factory set almost all the
way out (turned counterclockwise).
A tachometer (F/1) is necessary to adjust the adjusting
screws (H) and (L), because exceeding the permissible
maximum speed leads to overheating and under-lubrica-
tion.
This can damage the engine!
The only user-adjustable setting is the idle adjusting
screw (speed). If the blade rotates in idle (without the throttle
pressed), it is absolutely necessary to correct the idle
speed before using the tool!
Do not adjust the idle speed until the machine has been
completely assembled and checked!
Adjust the idle speed only with the engine warm, a clean
air filter, and properly installed cutting tool.
Use a screwdriver (F/2, blade width 4 mm, part No. 944 340
001) to adjust the screw.
F
1
2
SERVICE
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PS-340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PS-340 in the language / languages: English, French as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar PS-340

Dolmar PS-340 User Manual - German - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info