507686
13
Zoom out
Zoom in
Previous page
1/24
Next page
13
15. TROUBLES SHOOTING
16. WARRANTY
This product is warranted in accordance with legal
regulations for a 12 months period effective from the date
of purchase by the first user.
This warranty covers all material or production failures, it
does not include defects from normal wear & tear parts,
such as bearings, brushes, cables, plugs or accessories
like drills, drill bits, saw blades etc.; damage or defects
resulting from abuse, accidents or alterations; nor the
costs for transport.
We reserve the right to reject any claim where the
purchase cannot be verified or when it is clear that the
product was not maintained properly. (Clean ventilation
slots, carbon brushes serviced regularly.)
Your purchase ticket must be kept as proof for date of
purchase.
Your un-dismantled tool must be returned to your dealer in
an acceptably clean state, in its original blow molded case
if applicable to unit, accompanied by your proof of
purchase.
17. ENVIRONMENT
Should your machine need replacement after extended
use, do not put it in the domestic waste but dispose of it in
an environmentally safe way.
PROBLEM PROBABLE CAUSE CORRECTIVE ACTION
Engine does not start. Throttle chock not in the correct
position for the prevailing
conditions.
Move throttle chock to correct position.
Fuel tank is empty. Fill tank with fuel: refer to ENGINE OWNER’S MANUAL.
Air cleaner element is dirty. Clean air cleaner element: refer to ENGINE OWNER’S
MANUAL.
Spark plug loose. Tighten spark plug to 25-30 Nm.
Spark plug wire loose or
disconnected from plug.
Install spark plug wire on spark plug.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.
Spark plug is defective. Install new, correctly gapped plug: refer to ENGINE
OWNER’S MANUAL.
Carburetor is flooded with fuel. Remove air cleaner element and pull starter rope
continuously until carburetor clears itself and install air
cleaner element.
Faulty ignition module. Contact the service agent.
Engine difficult to start or
loses power.
Dirt, water, or stale fuel tank. Drain fuel and clean tank. Fill tank with clean, fresh fuel.
Vent hole in fuel tank cap is
plugged.
Clean or replace fuel tank cap.
Air cleaner element is dirty. Clean air cleaner element.
Engine operates
erratically.
Spark plug is defective. Install new, correctly gapped plug: refer to ENGINE
OWNER’S MANUAL.
Spark plug gap is incorrect. Set gap between electrodes at 0.7 to 0.8 mm.
Air cleaner element is dirty. Clean air cleaner element: refer to ENGINE OWNER’S
MANUAL.
Engine idles poorly. Air cleaner element is dirty. Clean air cleaner element: refer to ENGINE OWNER’S
MANUAL.
Air slots in engine shroud are
blocked.
Remove debris from shots.
Cooling fins and air passages
under engine blower housing are
blocked.
Remove debris from cooling fins and air passages.
Engine skips at high
speed.
Gap between electrodes of spark
plug is too close.
Set gap between electrodes at 0.7 to 0.8 mm.
Engine overheats. Cooling air flow is restricted. Remover any debris from slots in shroud, blower
housing, air passages.
Incorrect spark plug. Install RJ19LMC spark plug and cooling fins on engine.
Mower vibrates
abnormally.
Cutting assembly is loose. Tighten blade.
Cutting assembly is unbalanced. Balance blade.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar PM-5120 S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar PM-5120 S in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info