Manual Dolmar HT-6510 (page 11 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

507699

Zoom out

Zoom in

1/64

Removing or installing shear blade

CAUTION:

• Before removing or installing shear blade, always be

sure that the tool is switched off and unplugged.

• When replacing the shear blade, always wear gloves

without removing blade cover so that hands and face

does not directly contact the blade. Failure to do so

may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

• For specific way of removing and installing shear

blades refer to the reverse of a package for accessory

shear blades.

Removing the shear blades

Reverse the tool and loosen four screws. (Fig. 21)

NOTE:

• Be careful not to get your hands dirty as grease is

applied in the shear blade driving area.

Remove the under cover. (Fig. 22)

Remove the gear housing cover. (Fig. 23)

Set the crank at the angle as shown in the figure with a

slotted bit screwdriver. (Fig. 24)

Remove two screws from the shear blades and the shear

blade unit will be taken out. (Fig. 25)

CAUTION:

• Return the gear to the original position in such a

manner as it was installed if it should be taken away by

mistake.

Installing the shear blade

Prepare 4 removed screws (For under cover), 2 screws

(For shear blade), gear housing cover, under cover, and

new shear blades.

Adjust the crank position as shown in the figure. At this

time, apply some grease provided with new shear blades

to the periphery of the crank. (Fig. 26)

Overlap the oval hole in the upper blade with that in the

lower one. (Fig. 27)

Take out the blade cover from the old shear blades and fit

it onto the new ones for easy handling during the

replacement of blades. (Fig. 28)

Place the new shear blades on the tool so that the oval

holes in the shear blades fit onto the crank. Overlap the

holes in the shear blades with the screw holes in the tool

and then secure them with two screws. (Fig. 29)

Check the crank for smooth turn with a slotted bit

screwdriver. (Fig. 30)

Install the gear housing, under cover on the tool. Tighten

the screw firmly.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades does not operate properly,

there is a poor fit between the blades and crank. Redo

from the beginning.

Storage

The hook hole in the bottom of the blade cover is

convenient for hanging the tool from a nail or screw on the

wall. (Fig. 31)

Put the blade cover on the shear blades so that the blades

are not exposed. Store the tool out of the reach of children

carefully.

Store the tool in the place not exposed to water and rain.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

DOLMAR Authorized Service Centers, always using

DOLMAR replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your DOLMAR tool specified in this

manual. The use of any other accessories or

attachments might present a risk of injury to persons.

Only use accessory or attachment for its stated

purpose.

If you need any assistance for more details regarding

these accessories, ask your local DOLMAR Service

Center.

• Blade cover

• Hook complete

• Shear blade assembly

• Waist cord hook

• Arm cord hook

EC-DECLARATION OF CONFORMITY

ENH020-1

The undersigned, as authorized by, declare that the

DOLMAR machines,

TYPE:

HT-5510, HT-6510, HT-7510

complies with the standard safety and health

requirements of the pertinent EU guidelines:

EU machinery guideline 98/37/EC, Noise emission

2000/14/EG, EU EMC guideline 2004/108/EC.

The requirements of the above EU guidelines were

implemented chiefly on the basis of the following

standards: EN60745-2-15, EN 55014, EN61000. The

conformity assessment procedure 2000/14/EG was

performed per Annex V. The measured sound pressure

level (L

): is 86.5 dB (A). The measured sound power

level (L

) is 94.5 dB (A). The guaranteed sound power

level (Ld) is 96 dB (A). Uncertainty (K) is 0.7 dB (A).

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745-2-15:

Vibration emission (a

h, D

): 4.4 m/s

Uncertainty (K): 1.5 m/s

Hamburg, CE2008

For DOLMAR GmbH

Tamiro Kishima Rainer Bergfeld

Managing Director Managing Director

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar HT-6510 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar HT-6510 Manual

Product: