507693
13
Zoom out
Zoom in
Previous page
1/31
Next page
13
- Turn off the engine and remove the spark plug connector when replacing or sharpening cutting tools, also when cleaning the cutter or cutting
device or carrying out any maintenance.
- Never straighten or weld a damaged cutting blade.
- Inspect the cutting blades with the engine switched off at short, regular intervals for damage.
- (Detection of hairline cracks by means of tapping-noise test.) Beware the teeth are sharp.
- Clean the Hedge Trimmer at regular intervals and check that all screws and nuts are well tightened.
- Never service or store the Hedge Trimmer in the vicinity of naked ames to avoid res.
- Always wear leather gloves when handling or sharpening the blades, as they are sharp.
Blade sharpening
If the edges are rounded and do not cut well any more, grind off only the shaded
portions. Do not grind the contact surfaces (sliding surfaces) of the top and bottom
edges.
- Before grinding, be sure to secure the blade rmly and switch off the engine and
remove the spark plug cap.
- Wear gloves, protective glasses, etc.
- An edge ground too much at a time or ground many times will lose its hardened
layer. It becomes rounded and dull very quickly in use.
Blade adjustment
The blades will wear with long use. When you nd that trimming is not as good as
when the blades were new, adjust them as follows.
1. Turn nut
loose.
2. Bolt
in with the driver lightly till it stops turning, and then screw it back one
quarter.
3. Turn nut
tight, holding bolt at the same time with a Hex Wrench.
4. Lubricate the blades after adjustments above with light oil.
5. Start the engine and operate the engine throttle on and off for a minute.
6. Stop the engine and touch the blades with your hand. If they are warm enough for
you to keep your hand on, then you have made the proper adjustment. If they are
too hot for you to keep touching, give bolt a little more turnback and repeat 5 to
see if they are properly adjusted.
NOTE: Never fail to stop the engine before making the adjustment.
The blades have a slot around screw
. In case you nd dust in the end of any of the slots, clean it.
NOTE: For enough time of blade stop (EN774), be sure to make the blade adjustment before operation.
MAINTENANCE INSTRUCTIONS
10° 10°
45°
Disk grinder
Edge cross
section
Holding the disk grinder at
a 45° angle, grind the edge
off to the dotted line to
sharpen the rounded tip.
Hexagonal U nut
Truss bolt
Blade guide
Upper blade
Lower blade
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar HT-2475 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar HT-2475 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 5,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info