6
When turning on the motor:
Keep your feet away from the cutting tools.
Do not tilt the machine.
Do not stand in front of the discharge opening.
Never let your hands or other part of the body or
clothing place near moving parts.
Electrical safety
Check the connector plug on the machine ts into the
socket before use.
Never modify the connector plug.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the machine. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
Check the extension cable regularly for damage to the
insulation. Replace it if damaged.
If the connecting cable is damaged, withdraw the mains
plug immediately. A damaged cable may cause contact
with live parts and electric shock.
Never use damaged cord.
Keep the cord and extension cable away from cutting
tools and wheels. Cutting tools may damage the cable
and cause electric shock.
When using the machine outdoors, always use a
residual current-operated circuit-breaker (RCD) with an
operating current of 30 mA or less.
Use only extension cable for outdoor use with splash-
proofed connector. Its cross-section must be at least
1.5mm
2
for cable lengths up to 25m, and 2.5 mm
2
for
cable lengths over 25m.
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
Operation
Avoid operating on wet grass. Take particular attention
when working on wet grass to prevent slipping.
Hold the handle rmly with both hands during operation.
Keep the handle dry and clean to prevent accidents.
Do not run. Only walk during operation.
Pay particular attention to your footings when working
on a slope.
Do not work straight up or down on a slope. Always
work along horizontal line.
Be especially careful when turning the machine on a
slope.
Never work on a steep slope.
Pay extreme attention when reversing or pulling the
machine towards you.
Do not overreach. Keep proper footing and balance at
all times. This enables better control of the machine in
unexpected situations.
Always remember:
Keep your feet away from the cutting tools.
Do not tilt the machine.
Do not stand in front of the discharge opening.
Never let your hands or other part of the body or
clothing place near moving parts.
Do not force the machine. It does the job better and
safer at the rate for which it was designed. Frequent
overload may cause motor damage or re.
•
–
–
–
–
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
–
–
–
–
•
Switch off the motor and unplug:
Whenever leaving the machine unattended
Before clearing a blockage or any fault
Before checking, cleaning or working on the
machine
Before making any adjustments, changing
accessories or storing
When the machine hits a foreign object. Wait until
the machine cools down. Inspect the machine
and replace the parts if needed before continuing
operation
Whenever the machine starts vibrating or making
noise unusually
When attaching or removing grass catcher
When someone enters your working area
When crossing surface other than grass
When transporting.
Stop the cutting tool:
If you have to tilt the machine
When crossing surfaces other than grass
Transporting the machine to and from surfaces
to be worked.
Pay attention to the cutting tools. They do not stop
immediately after switch off.
Maintenance instructions
Have your machine serviced by our authorized service
center, always using only genuine replacement parts.
Incorrect repair and poor maintenance can shorten the
life of the machine and increase the risk of accidents.
Inspect the machine on regular base.
Before servicing, inspection, adjustment, storage, or to
change an accessory, take following steps:
Shut off the power source
Disconnect the machine from power supply
Make sure that all moving parts have come to a
complete stop
Allow the machine to cool.
Inspect on the machine for possible damage:
Whether safety devices works properly for its
intended function
Whether all the moving parts work smoothly and
adequately
Whether all parts are not damaged and properly
installed
Check the cutting tool for any damage, worn or
unbalance
Check the grass catcher regularly for any
damage or worn
Check all the nuts, bolts and screws are tight
Replace or repair by our authorized service
center if there are any damaged or worn parts.
Do not carry out maintenance or repair work other than
that described in this instruction manual. Any other
work must be carried out by Dolmar authorized service
center.
Only use original Dolmar replacement parts and
accessories intended for your machine. Otherwise
it may result in personal injury or damage on the
machine.
Store the machine in a dry room. Keep it out of reach of
children. Never store the machine outdoors.
•
–
–
–
–
–
–
–
–
–
–
•
–
–
–
•
•
•
•
–
–
–
–
•
–
–
–
–
–
–
–
•
•
•
