Manual Dolmar ES-39 TLC (page 13 of 28) (English, Dutch)

599930

Zoom out

Zoom in

1/28

emptied, add oil up to the bottom edge of the filler neck.

The oil delivery may otherwise be impaired.

To fill the oil, perform the following steps: (Fig. 18)

1. Clean the area around the oil filler cap thoroughly to

prevent any dirt from entering the oil tank.

2. Unscrew the oil filler cap and add oil up to the lower

edge of the filler neck.

3. Screw the oil filler cap firmly back in place.

4. Wipe away any spilt chain oil carefully.

NOTE:

• When the chain saw is used for the first time, it may

take up to two minutes for the saw chain oil to begin its

lubricating effect upon the saw mechanism. Run the

saw without load until it does so (see “CHECKS”).

CHECKS

Before starting work, carry out the following checks:

Checking the chain tension

WARNING:

• Always withdraw the mains plug before checking the

chain tension, and wear safety gloves.

Make sure the saw chain fits snugly against the lower side

of the bar (see circle). (Fig. 12)

Check the chain tension frequently, as new chains are

subject to elongation.

Excessively high tension of saw chain may cause

breakage of saw chain, wear of the guide bar and

breakage of the adjusting dial.

A chain which is too loose can jump off the bar, and

therefore presents an accident risk.

If the chain is too loose: Refer to the section titled

“Adjusting saw chain tension” and adjust the saw chain

tension again.

Checking the switch action

CAUTION:

Before plugging in the tool, always check to see that the

switch trigger actuates properly and returns to the “OFF”

position when released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Do not pull the switch trigger hard without depressing the

lock-off button. This may cause switch breakage.

Checking the chain brake

NOTE:

• If the chain saw fails to start, check whether the chain

brake is released. To release the chain brake, pull the

hand guard backwards firmly until you feel it engage.

(Fig. 19 & 20)

Check the chain brake as follows:

1. Hold the chain saw with both hands when switching it

on. Hold the rear handle with your right hand, the front

handle with your left. Make sure that the bar and the

chain do not contact with any object.

2. First press the lock-off button, then the switch trigger.

The saw chain starts immediately.

3. Press the front hand guard forwards using the back of

your hand. Make sure that the saw chain comes to an

immediate standstill.

CAUTION:

• If the saw chain does not stop immediately, do not use

the saw under any circumstances. Consult DOLMAR

authorized service centers.

Checking the run-down brake

Switch on the chain saw.

Release the switch trigger completely. Make sure the saw

chain comes to a standstill within a second.

CAUTION:

• If the saw chain does not stop immediately, do not use

the saw under any circumstances. Consult DOLMAR

authorized service centers.

Checking the chain oiler

Before starting work, check the oil level in the tank, and

the oil delivery.

The oil level can be seen in the oil level sight shown in the

figure. (Fig. 21)

Check the oil delivery as follows:

Start the chain saw.

With the saw running, hold the saw chain approximately

15 cm above a tree trunk or the ground. If lubrication is

adequate, the oil spray will produce a light oil trace.

Observe the wind direction, and do not expose yourself to

the oil spray unnecessarily.

CAUTION:

• If an oil trace is not formed, do not use the saw. The

lifespan of the chain will otherwise be reduced. Check

the oil level. Clean the oil feed groove and the oil feed

hole in the bar (refer to “MAINTENANCE”).

Adjusting the chain lubrication (Fig. 22)

You can adjust the oil pump feed rate with the adjusting

screw.

CAUTION:

• Always use a front handle and rear handle and firmly

hold the tool by both front handle and rear handle

during operations.

• Always secure the timber to be cut, otherwise the cut

fragments may cause personal injury.

WORKING WITH THE CHAIN SAW

Bucking (Fig. 23)

For bucking cuts, rest the spike bumper shown in the

figure on the wood to be cut.

With the saw chain running, saw into the wood, using the

rear handle to raise the saw and the front one to guide it.

Use the spike bumper as a pivot.

Continue the cut by applying slight pressure to the front

handle, easing the saw back slightly. Move the spike

bumper further down the timber and raise the front handle

again.

When making several cuts, switch the chain saw off

between cuts.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-39 TLC in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar ES-39 TLC Manual

Product: