Manual Dolmar ES-2141 (page 11 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

599925

Zoom out

Zoom in

1/124

– Maintain a firm grip, with thumbs and fingers

encircling the chain saw handles, with both

hands on the saw and position your body and

arm to allow you to resist kickback forces.

Kickback forces can be controlled by the operator,

if proper precautions are taken. Do not let go of the

chain saw. (Fig. 1)

– Do not overreach and do not cut above

shoulder height. This helps prevent unintended tip

contact and enables better control of the chain saw

in unexpected situations.

– Only use replacement bars and chains

specified by the manufacturer. Incorrect

replacement bars and chains may cause chain

breakage and/or kickback.

– Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

ADDITIONAL SAFETY RULES

1. Read the instruction manual in order to familiarize

yourself with operation of the chain saw.

2. Before using the chain saw for the first time, arrange

to have instruction in its operation. If this is not

possible, at least practice cutting round timber on a

trestle before beginning work.

3. The chain saw must not be used by children or young

persons under 18 years of age. Young persons over

16 years of age may be exempted from this restriction

if they are undergoing training under the supervision

of an expert.

4. Working with the chain saw requires a high level of

concentration. Do not work with the saw if you are not

feeling fit and well. Carry out all work calmly and

carefully.

5. Never work under the influence of alcohol, drugs or

medication.

Proper use

1. The chain saw is intended solely for cutting wood. Do

not use it for example to cut plastic or porous

concrete.

2. Only use the chain saw for operations described in

this instruction manual. Do not, for example, use it to

trim hedges or for similar purposes.

3. The chain saw must not be used for forestry work, i.e.

for felling and limbing standing timber. The chain saw

cable does not provide the operator with the mobility

and safety required for such work.

4. The chain saw is not intended for commercial use.

5. Do not overload the chain saw.

Personal protective equipment

1. Clothing must be close-fitting, but must not obstruct

mobility.

2. Wear the following protective clothing during work:

• A tested safety helmet, if a hazard is presented by

falling branches or similar;

• A face mask or goggles;

• Suitable ear protection (ear muffs, custom or

mouldable ear plugs). Octave brand analysis upon

request.

• Firm leather safety gloves;

• Long trousers manufactured from strong fabric;

• Protective dungarees of cut-resistant fabric;

• Safety shoes or boots with non-slip soles, steel

toes, and cut-resistant fabric lining;

• A breathing mask, when carrying out work which

produces dust (e.g. sawing dry wood).

Protection against electric shock

The chain saw must not be used in wet weather or

damp environments, as the electric motor is not

waterproof.

1. Only plug the saw into sockets in tested electrical

circuits. Check that the system voltage matches that

on the rating plate. Ensure that a 16 A line fuse is

fitted. Saws used in the open air must be connected to

a residual current-operated circuit-breaker with an

operating current no higher than 30 mA.

Should the connecting cable be damaged,

withdraw the mains plug immediately.

Safe working practices

1. Before starting work, check that the chain saw is in

proper working order and that its condition complies

with the safety regulations. Check in particular that:

• The chain brake is working properly;

• The run-down brake is working properly;

• The bar and the sprocket cover are fitted correctly;

• The chain has been sharpened and tensioned in

accordance with the regulations;

• The mains cable and mains plug are undamaged;

Refer to the “CHECKS” section.

2. Always ensure in particular that the extension cable

used is of adequate cross-section (see

“SPECIFICATIONS”). When using a cable reel, wind

the cable completely off the reel. When using the saw

in the open air, ensure that the cable employed is

intended for open-air use and is rated accordingly.

3. Keep the cord away from the cutting area and to

position cord so that it will not be caught on branches,

and the like, during cutting.

4. Do not operate the chain saw in the vicinity of

flammable dust or gases, as the motor generates

sparks and presents a risk of explosion.

5. Work only on firm ground and with a good footing. Pay

particular attention to obstacles (e.g. the cable) in the

working area. Take particular care where moisture,

ice, snow, freshly cut wood or bark may make

surfaces slippery. Do not stand on ladders or trees

when using the saw.

6. Take particular care when working on sloping ground;

rolling trunks and branches pose a potential hazard.

7. Never cut above shoulder height.

8. Hold the chain saw with both hands when

switching it on and using it. Hold the rear handle

with your right hand and the front handle with your left.

Hold the handles firmly with your thumbs. The bar and

the chain must not be in contact with any objects when

the saw is switched on. (Fig. 1)

9. Clean the area to be cut of foreign objects such as

sand, stones, nails, wire, etc. Foreign objects damage

the bar and chain, and can lead to dangerous

kickback.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-2141 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar ES-2141

Dolmar ES-2141 User Manual - Dutch - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar ES-2141 Manual

Product: