599926

Dolmar ES-2141 TLC Manual

17
Zoom out
Zoom in
Previous page
1/124
Next page
17
Maintaining the chain and run-down
brakes
The braking systems are very important safety features.
Like any other component of the chain saw, they are
subject to a certain degree of wear. They must be
inspected regularly by DOLMAR authorized service
centers. This measure is for your own safety.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes. (Fig. 44)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
After replacing brushes, plug in the tool and break in
brushes by running tool with no load for about 10 minutes.
(Fig. 45)
Storing tool
Biologically degradable saw chain oil can only be kept for
a limited period. Beyond two years after manufacture,
biological oils begin to acquire an adhesive quality, and
cause damage to the oil pump and components in the
lubricating system.
– Before taking the chain saw out of service for a longer
period, empty the oil tank and fill it with a small quantity
of engine oil (SAE 30).
– Run the chain saw briefly to flush all residue of the
biological oil out of the tank, lubricating system and
saw mechanism.
NOTE:
• When the chain saw is taken out of service, small
quantities of chain oil leaks from it for some time
afterwards. This is normal, and is not a sign of a fault.
Store the chain saw on a suitable surface.
Before returning the chain saw to service, fill up with fresh
BIOTOP saw chain oil.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by DOLMAR Authorized Service Centers,
always using DOLMAR replacement parts.
TROUBLE SHOOTING
Before asking for repairs, conduct your own inspection
first. If you find a problem that is not explained in the
manual, do not attempt to dismantle the tool. Instead, ask
Dolmar Authorized Service Centers.
014314
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Dolmar tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Dolmar Service Center.
• Saw chain
• Guide bar cover
• Guide bar
• Saw chain oil
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
Noise
ENG905-1
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
): 90.8 dB (A)
Sound power level (L
WA
): 101.8 dB (A)
Uncertainty (K): 2.5 dB (A)
Wear ear protection.
Malfunction status Possible cause Remedy
The chain saw does not start.
No power supply.
Connect to the power supply.
Check the power supply.
Cable defective.
Stop using the tool immediately, and ask your local
authorized service center.
Tool malfunction.
Stop using the tool immediately, and ask your local
authorized service center.
Chain does not run. Chain brake is engaged. Release chain brake.
Insufficient performance. Carbon brush worn down. Ask your local authorized service center for repair.
No oil on the chain.
Oil tank is empty. Fill the oil tank.
Oil guide groove is dirty. Clean the groove.
Oil pump adjusting screw
incorrectly adjusted.
Adjust the oil pump feed rate.
Chain does not stop even the
chain brake is engaged.
Brake band worn down.
Stop using the tool immediately, and ask your local
authorized service center.
The tool vibrates abnormally.
Loose guide bar or saw chain. Adjust the guide bar and saw chain tension.
Tool malfunction.
Stop using the tool immediately, and ask your local
authorized service center.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar ES-2141 TLC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-2141 TLC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar ES-2141 TLC

Dolmar ES-2141 TLC User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info