Manual Dolmar ES-2131 (page 13 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

599921

Zoom out

Zoom in

1/124

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

DESIGNATION OF PARTS

(Nut model: the sprocket cover is tightened by nuts.)

For Model ES-154, ES-164, ES-174, ES-184, ES-2131,

ES-2136, ES-2141, ES-2146 (Fig. 5)

(Lever model: the sprocket cover is tightened by lever.)

For Model ES-154 TLC, ES-164 TLC, ES-174 TLC,

ES-184 TLC, ES-2131 TLC, ES-2136 TLC,

ES-2141 TLC, ES-2146 TLC (Fig. 6)

(For all models) (Fig. 7)

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Removing or installing sprocket cover

To remove the sprocket cover, perform the following

steps:

(For nut models) (Fig. 8)

Loosen the nut.

(For lever models) (Fig. 9)

Press and fully open the lever until it stops.

Turn the lever counterclockwise.

To install the sprocket cover, perform the above steps in

reverse.

Removing or installing saw chain

CAUTION:

• Always wear gloves when installing or removing the

saw chain.

To remove the saw chain, perform the following steps:

1. Loosen the sprocket cover.

2. (For nut models) Turn the chain adjusting screw

counterclockwise to release the saw chain tension.

(For lever models) Turn the adjusting dial to “-”

direction to loosen the saw chain tension. (Fig. 10 &

11)

3. Remove the sprocket cover.

4. Remove the saw chain and guide bar from the chain

saw.

To install the saw chain, perform the following steps:

5. Make sure the direction of the chain. The arrow mark

on the chain shows the direction of the chain. (Fig. 12)

6. Fit in one end of the saw chain on the top of the guide

bar and the other end of it around the sprocket.

7. Place the guide bar on the chain saw.

8. Align the tension slide with the hole of the guide bar.

(Fig. 13)

9. Holding the guide bar, and turn the chain adjusting

screw/dial to adjust the saw chain tension.

10. Place the sprocket cover so that the hooks fit

alongside the holes and the pin fits its counterpart on

the sprocket cover. (Fig. 14)

11. Tighten the sprocket cover. (Fig. 15 & 16)

Adjusting saw chain tension

The saw chain may become loose after many hours of

use. From time to time check the saw chain tension

before use.

1. Loosen the sprocket cover lightly.

2. Lift up the guide bar tip slightly.

3. Turn the adjusting screw/dial to adjust saw chain

tension. (Fig. 17 & 18)

4. Tighten the saw chain until the lower side of the saw

chain fits in the guide bar rail (see circle).

5. Keep holding the guide bar lightly, tighten the sprocket

cover after adjusting the chain tension. Make sure that

the saw chain does not loose at lower side.

Make sure the saw chain fits snugly against the lower side

of the bar.

CAUTION:

• Do not tighten the saw chain too much. Excessively

high tension of saw chain may cause breakage of saw

chain, wear of the guide bar and breakage of the

adjusting dial.

• A chain which is too loose can jump off the bar, and

therefore presents an accident risk.

• Carry out the procedure of installing or removing saw

chain in a clean place free from sawdust and the like.

Engaging extension cord

CAUTION:

• Make sure that the extension cord is unplugged to the

mains outlet. (Fig. 19)

When engaging the extension cord, secure it to the chain

saw’s cord with the cord hook.

Attach the cord hook about 100 - 200 mm from the

extension cord connector. This helps prevent

unintentional disconnection.

OPERATION

CAUTION:

• Hold the tool firmly with right hand on the rear handle

and left hand on the front handle when performing the

tool.

Switch action (Fig. 20)

CAUTION:

• Always be sure that the tool is switched off and

unplugged before checking function on the switch

trigger.

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To prevent the switch trigger from being accidentally

pulled, a lock-off button is provided.

To start the tool, depress the lock-off button and pull the

switch trigger. Release the switch trigger to stop.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-2131 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar ES-2131

Dolmar ES-2131 User Manual - Dutch - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar ES-2131 Manual

Product: