Manual Dolmar ES-164 TLC (page 12 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

599917

Zoom out

Zoom in

1/124

10. Take particular care when cutting in the vicinity of wire

fences. Do nut cut into the fence, as the saw may kick

back.

11. Do not cut into the ground.

12. Cut pieces of wood singly, not in bunches or stacks.

13. Avoid using the saw to cut thin branches and roots, as

these can become entangled in the chain saw. Loss of

balance presents a hazard.

14. Use a secure support (trestle) when cutting sawn

timber.

15. Do not use the chain saw to prise off or brush away

pieces of wood and other objects.

16. Guide the chain saw such that no part of your body is

within the extended path of the saw chain (see figure).

(Fig. 2)

17. When moving around between sawing operations,

apply the chain brake in order to prevent the chain

from being operated unintentionally. Hold the chain

saw by the front handle when carrying it, and do not

keep your finger on the switch.

18. Withdraw the mains plug when taking breaks or

leaving the chain saw unattended. Leave the chain

saw where it cannot present a hazard.

Kickback

1. Hazardous kickback may arise during work with the

chain saw. Kickback arises when the tip of the bar (in

particular the upper quarter) comes into contact with

wood or another solid object. This causes the

chainsaw to be deflected in the direction of the

operator. (Fig. 3)

2. In order to avoid kickback, observe the following:

• Never begin the cut with the tip of the bar.

• Never use the tip of the bar for cutting. Take

particular care when resuming cuts which have

already been started.

• Start the cut with the chain running.

• Always sharpen the chain correctly. In particular,

set the depth gauge to the correct height.

• Never saw through several branches at a time.

• When limbing, take care to prevent the bar from

coming into contact with other branches.

• When bucking, keep clear of adjacent trunks.

Always observe the bar tip.

• Use a trestle.

Safety features

1. Always check that the safety features are in working

order before starting work. Do not use the chain saw if

the safety features are not working properly.

– Chain brake:

The chain saw is fitted with a chain brake which brings

the saw chain to a standstill within a fraction of a

second. It is activated when the hand guard is pushed

forwards. The saw chain then stops within 0.15 s, and

the power supply to the motor is interrupted. (Fig. 4)

– Run-down brake:

The chain saw is equipped with an run down brake

which brings the saw chain to an immediate stop when

the ON/OFF switch is released. This prevents the saw

chain from running on when switched off, and thus

presenting a hazard.

–The front and rear hand guards protect the user

against injury from pieces of wood which may be

thrown backwards, or a broken saw chain.

–The trigger lockout prevents the chain saw from being

switched on accidentally.

–The chain catcher protects the user against injury

should the chain jump or break.

Transport and storage

When the chain saw is not in use or is being

transported, withdraw the mains plug and fit the

guide bar cover supplied with the saw. Never carry

or transport the saw with the saw chain running.

1. Carry the chain saw by the front handle only, with the

bar pointing backwards.

2. Keep the chain saw in a secure, dry and locked room

out of the reach of children. Do not store the chain saw

outdoors.

Maintenance

1. Withdraw the plug from the socket before carrying out

any adjustments or maintenance.

2. Check the power cable regularly for damage to the

insulation.

3. Clean the chain saw regularly.

4. Have any damage to the plastic housing repaired

properly and immediately.

5. Do not use the saw if the switch trigger is not working

properly. Have it properly repaired.

6. Under no circumstances should any modifications be

made to the chain saw. Your safety is at risk.

7. Do not carry out maintenance or repair work other

than that described in this instruction manual. Any

other work must be carried out by authorized service

centers.

8. Only use genuine replacement parts and accessories

intended for your model of saw. The use of other parts

increases the risk of accident.

9. We accept no responsibility for accidents or damage

should non-approved bars, saw chains or other

replacement parts or accessories be used.

First aid

Do not work alone. Always work within shouting

distance of a second person.

1. Always keep a first-aid box to hand. Replace any

items taken from it immediately.

2. Should you request assistance in the event of an

accident, state the following:

• Where did the accident happen?

• What happened?

• How many persons are injured?

• What injuries do they have?

• Who is reporting the accident?

NOTE:

Individuals with poor circulation who are exposed to

excessive vibration may experience injury to blood

vessels or the nervous system.

Vibration may cause the following symptoms to occur in

the fingers, hands or wrists: “Falling asleep” (numbness),

tingling, pain, stabbing sensation, alteration of skin colour

or of the skin.

If any of these symptoms occur, see a physician!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-164 TLC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar ES-164 TLC

Dolmar ES-164 TLC User Manual - Dutch - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar ES-164 TLC Manual

Product: