Manual Dolmar AY-1820H (page 16 of 28) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598412

Zoom out

Zoom in

1/28

Attaching the chip receiver (optional accessory) on the

tool when trimming the hedge straight can avoid cut off

leaves’ being thrown away. (Fig. 46)

To cut a hedge side evenly, it helps to cut from the bottom

upwards. (Fig. 47)

Trim boxwood or rhododendron from the base toward the

top for a nice appearance and good job.

Installing or removing chip receiver

(optional accessory)

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing chip receiver.

NOTE:

• When replacing the chip receiver, always wear gloves

so that hands and face does not directly contact the

blade. Failure to do so may cause personal injury.

• When replacing the chip receiver, always be careful not

to contact the shear blades.

• The chip receiver receives cut-off leaves and alleviates

collecting thrown-away leaves. This can be installed on

either side of the tool. (Fig. 48)

Place the chip receiver on the shear blades so that its slits

overlap with the screws on the shear blades and secure it

using two clamping nuts.

To remove the chip receiver, loosen and remove the two

clamping nuts and then take it out.

Storage (Fig. 49)

The hook hole in the tool bottom is convenient for hanging

the tool from a nail or screw on the wall.

Put the blade cover on the shear blades so that the blades

are not exposed. Store the tool out of the reach of children

carefully.

Store the tool in the place not exposed to water and rain.

Noise

ENG905-1

The typical A-weighted noise level determined according

to IEC60335:

Sound pressure level (L

): 78 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to IEC60335:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

Hedge trimming operation with optional hedge shear

blades

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 74 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH025-3

EC Declaration of Conformity

The undersigned, Tamiro Kishima and Rainer

Bergfeld, as authorized by Dolmar GmbH, declare that

the DOLMAR machine(s):

Designation of Machine:

Cordless Grass Shear

Model No./ Type: AX-1820H, AY-1820H

are of series production and

Conforms to the following European Directives:

2006/42/EC

And are manufactured in accordance with the following

standards or standardised documents:

EN60745, IEC60335

The technical documentation is on file at:

Dolmar GmbH,

Jenfelder Straße 38, Abteilung FZ,

D-22045 Hamburg

7.7.2011

Tamiro Kishima Rainer Bergfeld

Managing Director Managing Director

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar AY-1820H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar AY-1820H Manual

Product: