Manual Dolmar AX-1820H (page 14 of 28) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598411

Zoom out

Zoom in

1/28

base plate of shear blades are positioned in the center of

these overlapped oval holes. (Fig. 18)

Turn the shear blades upside down and install it so that

the pins on the tool fit in the hole in the shear blades.

Make sure that the shear blades are set in place securely

as far as they reach the base plate. (Fig. 19)

Place the undercover so that the symbol on the

undercover is aligned with the symbol Δ on the locking

lever. (Fig. 20)

Press the undercover down and turn the undercover

clockwise while pressing it down until the symbol on

the label is aligned with the symbol Δ on the locking lever

(the undercover is completely locked.). (Fig. 21)

At this time, make sure that the locking lever fits in the

groove in the undercover.

Remove the blade cover and then turn on the tool to

check it for proper movement.

NOTE:

• When the shear blades do not operate properly, there

is a poor fit between the blades and crank. Redo from

the beginning.

OPERATION

WARNING:

• Keep hands away from blades.

CAUTION:

• Smear the blade before and once per hour during

operation using machine oil or the like.

• Avoid operating the tool under the scorching sunlight

as much as practicable. When operating the tool, be

careful of your physical conditions. (Fig. 22)

Turn the tool on after adjusting the shearing height and

hold it so that the foot of the tool rest on the ground. Then

gently move the tool forward into the area to be cut.

(Fig. 23)

When trimming around curb, fence or trees, move the tool

along them. Be careful for the blade not to contact them.

(Fig. 24)

When trimming sprouts or foliage of a small tree, remove

the base frame from the tool and cut little by little.

Shear big branches to your desired height beforehand

using branch scissors before using this tool.

CAUTION:

• When trimming twigs and foliage, do not attempt to trim

too much at a time. Proceed gently. Also do not

attempt to cut thick branches.

• Do not let the shear blades contact the grounds during

operation. The blades will be dulled, causing poor

performance.

• Do not trim wet grass or foliage of small trees.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Cleaning the tool

Clean out the tool by wiping off dust with a dry or soap-

dipped rag.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Shear blade maintenance (Fig. 25 & 26)

After operation, remove dust from both sides of the blade

with wired brush, wipe off it with a rag and then apply

enough low-viscosity oil, such as machine oil etc. and

spray-type lubricating oil.

CAUTION:

• Do not wash the blades in water. Failure to do so may

cause rust or damage on the tool.

• Dirt and corrosion cause excessive blade friction and

shorten the operating time per battery charge.

After use

• To clean off the exterior of the tool, dampen a soft cloth

in a soapy water and wipe gently. Never use thinner or

benzine.

• Do not store the tool in a place where volatile materials

are stored.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Dolmar Authorized Service Centers, always

using Dolmar replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Dolmar tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Dolmar Service Center.

• Grass shear blade assembly

• Grass shear blade cover

• Base frame

• Battery cartridge BL1013

• Battery charger DC10WA

• Long handle attachment

For cordless hedge trimmer use

This tool can be used as a hedge trimmer by using the

hedge shear blade (optional accessory) and 2-way

change set (optional accessory).

To use this tool as a hedge trimmer, replacing the grass

shear blades with the hedge shear blades is required.

For removing the grass shear blades, refer to the

aforementioned section titled “Installing or removing grass

shear blades”. For installing the hedge shear blades, refer

to the section below titled “Installing or removing hedge

shear blades”.

• Hedge shear blade assembly (for Hedge Trimmer)

• 2-way change set consisting of the following two

accessories

• Hedge shear blade cover (for Hedge Trimmer)

• Storage case (for blade bottom section) (Fig. 27)

• Chip receiver for hedge trimming (for Hedge Trimmer)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar AX-1820H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar AX-1820H Manual

Product: