507648
11
Zoom out
Zoom in
Previous page
1/28
Next page
11
- Turn the chain tightener (G/6) to the right (clockwise)
until the chain engages the guide groove of the bottom
side of the bar (see circle). Press the guide bar against the
housing with your left hand.
- Replace the sprocket guard (H/4).
- Manually tighten the retaining nuts (H/3).
Chain brake
J
Tightening the saw chain
- Slightly lift the end of the guide bar and turn the chain adjust-
ing screw (I/6) to the right (clockwise) until the chain rests
against the bottom side of the guide bar.
- While still holding up the tip of the guide bar, tighten the
retaining nuts (H/3) with the universal wrench.
G H
6
K
L
I
6
1
2
3
4
3
Checking the chain tension
- The tension of the chain is correct if the chain rests against
the bottom side of the guide bar and can still be easily turned
by hand.
- While doing so the chain brake must be released.
- Check the chain tension frequently - new chains tend to get
longer during use!
- When checking the chain tension the engine must be switched
off.
NOTE:
It is recommended to use 2-3 chains alternatively.
In order to guarantee uniform wear of the guide bar the bar
should be turned over whenever replacing the chain.
Engaging the chain brake (braking)
If the kickback is strong enough the sudden acceleration of the
guide bar combined with the inertia of the hand guard (L/3) will
automatically actuate the chain brake.
To engage the chain brake manually, simply push the hand guard
(L/3) forward (towards the tip of the saw) with your left hand (arrow 1).
Releasing the chain brake
Pull the hand guard (L/3) towards you (arrow 2) until you feel
it catch. The brake is now released.
The DOLMAR models comes with an inertia chain brake as
standard equipment. If kickback occurs due to contact of the
guide-bar tip with wood (see SAFETY PRECAUTIONS, page
6), the chain brake will stop the chain through inertia if the
kickback is sufÞ ciently strong. The chain will stop within a frac-
tion of a second.
The chain brake is installed to block the saw chain before
starting it and to stop it immediately in case of an emer-
gency. MPORTANT: NEVER run the saw with the chain brake
activated (except for testing, see “Testing chain brake”)! Doing
so can very quickly cause extensive engine damage!
ALWAYS release the chain brake before starting
the work!
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar 111 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar 111 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar 111

Dolmar 111 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info