Manual Dogtrace d-control 202 mini (page 6 of 20) (English)

766069

Zoom out

Zoom in

1/20

d–control 200 mini

Electronic training collar –

basic training set for one dog

d–control 202 mini

Electronic training collar –

basic training set for two dogs –

with a carrying case

User Guide

Declaration of Conformity

We:

VNT electronics s.r.o.

Smetanovo náměstí 104

570 01, Litomyšl

IČO: 64793826

declare under own responsibility that the product:

Electronic training collar

Dogtrace d-control 200 mini

is in compliance with essential requirements and other relevant provisions of

Directive 1999/5/EC from 9. 3. 1999

meets requirements of General Licence of The Czech Telecommunication Oce

according to general licence no. VO-R/10/05.2014-3, and corresponds to the following standarts:

ETSI EN 301 489-1 V1.9.2

ETSI EN 301 489-3 V1.6.1

ETSI EN 300 220-2 V.2.4.1

ETSI EN 60950-1:2006

The product is safe on condition of commonly used in conformity with instruction

manual. The Declaration of Conformity is created in exclusive responsibility of producer.

Measuring report no.: 6440-7600/2008 issued by certicated laboratory no.1103 VTÚPV Vyškov

Measuring report no.: 6440-697/2008 issued by certicated laboratory no.1103 VTÚPV Vyškov

This declaration of Conformity is created in exclusive responsibility of producer.

In Litomyšl 28.8.2014

Ing. Jan Horák

executive director

Tel.: +420 731 441 541

info@dogtrace.com

www.dogtrace.com

WARNING:

The person with a personal instrument to support heart activity (pacemaker, debrillator) must

respect the relevant precautionary measures. The d–control emits a certain stationary

magnetic eld (lower part of the remote controller and RF signals).

Frequency= 869, 525 MHz, maximum transmitted power = 25 mW.

Contents

Introduction ................................................................................ 4

Package contents ........................................................................... 4

Optional accessories ........................................................................ 4

Product description ......................................................................... 5

Battery insertion and replacement .......................................................... 6

Choosing the contact points ................................................................ 7

Switching ON/OFF .......................................................................... 8

Programming (coding) the transmitter with the receiver ..................................... 9

Transmitter - button functions .............................................................10

How to check that your d–control works correctly ..........................................12

Using d–control training collar in winter ....................................................12

Getting the best results ...................................................................13

Training tips ............................................................................... 14

Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance ...............................................................................15

Troubleshooting ........................................................................... 16

Technical specications ....................................................................17

Warranty terms and conditions .............................................................18

Certicate of warranty .....................................................................20

Hereby, VNT electronics s.r.o. , declares that this d-control 200 mini is in compliance

with the essential requirements and other relevant provisions

of Directive 1999/5/EC.

Introduction

Package contents

Optional accessories

The electronic training collar Dogtrace d–control, consisting of the transmitter and the receiver, it is a

modern, safe, reliable, and eective training tool. With the d-control training collar you can make

corrections that are suited to your dog‘s temperament and the distraction level of the moment, at the

proper time, for maximum training eciency. However, correcting to stop unwanted behaviour is only

a small part of what you can do with the d-control. More importantly, the d-control is a powerful tool

for encouraging desired behaviour. It is possible to easily adjust the intensity of the stimulation.

Thanks to the ergonomic design and low weight of the receiver, it is suitable for all dog breeds and

sizes.

 Collar unit (receiver) with the strap (two receivers for d–control 202 mini)

 Two pairs of contact points (short - 12 mm and long - 17 mm)

 Two lithium CR2 3V batteries (3 pcs for d–control 202 mini)

 Transmitter (remote control) with the belt clip

 User guide and certicate of warranty

 Carrying case (for d–control 202 mini)

 Test discharge lamp

 Transmitter neck strap

 Additional receiver

 Dummy receiver

 Spare screws

 Silicone grease

 Spare contact points (12 mm, 17 mm, 21 mm)

 Spare lithium CR2 3V batteries

 Spare rubber seal

 Woven or plastic collars - various colours

Product description

TRANSMITTER RECEIVER

TRANSMITTER - 1 - Backlit LCD display, 2 - Booster button, 3 - Stimulation button, 4 - Tone signal

button, 5 - ON/OFF Switch, 6 - Adjustment of the level of the stimulation, 7 - Dog selection button

(dog A, dog B)

RECEIVER - 1 - Strap, 2 - Contact points, 3 - ON/OFF LED Indicator, 4 - indicator area where the

ON/OFF magnetic switch is located

DISPLAY - 1 - Indicator of the radio transmission, 2 - Battery power indicator, 3 - Stimulation level

indicator (from 0 to 19), 4 - Dog selection indicator (dog A, dog B)

LCD DISPLAY

1 2

Battery insertion and replacement

INSERTION (REPLACEMENT) OF THE BATTERY IN THE RECEIVER

 Unscrew the 4 screws of the top of the receiver using a cross-head screwdriver and remove the lid.

Insert the lithium CR2 3V battery into the battery compartment. Please check that and the battery

is installed with correct polarity (according to the polarity indicated with the "+" symbol in the

battery compartment - see the picture). Wrong polarity may damage the unit.

 A beep sound is emitted indicating the correct installation of the battery.

 If the beep sound is not emitted after the battery is inserted, remove it immediately. Initialize the

system by using a metal tool (e.g. a screwdriver, scissors, etc.) and short-circuit (connect) both

contacts of the battery holder for about 2 seconds (see the picture on the page 16). Please check

the correct polarity and try to insert the battery again.

 Before putting the lid of the receiver back in place, make sure that the rubber seal is correctly

seated in its groove. Screw down the 4 screws of the top tightly (do not over tighten them).

Checking the battery status

LED indicator on the receiver‘s front cover indicates the status of

the battery:

Checking the battery status

 Green ashing LED indicates the battery is fully charged.

 Red and green ashing LEDs together indicate low battery.

Prepare a spare lithium CR2 3V battery and follow the

instructions described in the section "Battery insertion and

replacement".Make sure that the receiver works correctly.

INSERTION (REPLACEMENT) OF THE BATTERY IN THE TRANSMITTER

Observe polarity when installing the battery. Reversing the battery will damage the transmitter. Use

only lithium CR2 3V batteries.

Battery polarity marks

TIP: You can easily lift up the battery using

the small flat-head screwdriver.

TIP

 Remove the transmitter battery cover using a cross-head

screwdriver.

 If replacing the battery, remove the old battery and dispose of it

properly.

 Place the lithium CR2 3V battery in the holder and press into place.

 Put the battery cover back into place and secure with screw.

The battery level is shown at the battery life status bar on the LCD

display.

 Battery fully charged: full battery icon is shown on the LCD display.

 Low battery: battery empty icon is shown on the LCD display.

Prepare a spare lithium CR2 3V battery and follow the instructions

described in the section "Insertion (replacement of the battery in

the transmitter".

Choosing the contact points

The stimulation is delivered through the receiver contact points. Two different series of contact points

are supplied. The length of the contact points must be sufficient to have proper contact with the dog‘s

skin, enabling the device to operate correctly. If you have a short-haired dog use the short 12 mm

contact points, if you have a long-haired dog replace them with the longer 17 mm contact points

supplied with the kit. Carefully tighten them manually (do not use a key). It is possible to purchase the

21 mm long contact points.

Switching ON/OFF

Switching ON/OFF the transmitter/Programming the transmitter with the receiver

SWITCHING THE TRASNMITTER ON/OFF

 Switching on: Press down for 1 second the button on the transmitter.

The LCD display indicates that the unit is active.

 Switching o: Again, press down for 1 second the button on the transmitter.

SWITCHING THE RECEIVER ON/OFF

A magnet located at the lower part of the transmitter is used to activate or deactivate the magnetic

switch located in the receiver.

 Switching on: approach the low area of the transmitter where the magnet is located until coming

close to the indicator located on the receiver (see the picture), hold for 1 second, the receiver

LED indicator will ash in green indicating the receiver is ON.

 Switching o: approach the low area of the transmitter where the magnet is located until coming

close to the indicator located on the receiver, hold for 1 second,

the receiver LED indicator will ash from green to red indicating

the receiver is OFF.

To extend the battery life it is necessary to switch o both receiver and

transmitter after the training is nished. If the battery will not be in use

for a month or longer, it is recommended that it is removed from the

receiver.

Programming (coding) the transmitter with the receiver

Each transmitter has its own operational code. The programming of the transmitter with the receiver

enables the two units to work together. This operation will help you to program the receiver to work

with a new transmitter or to program a new receiver to work with your existing transmitter. Receiver

can be reprogrammed indenitely, either with the same transmitter or a new d-control transmitter. It

is possible to program an unlimited number of receivers to one transmitter.

 Switch on the transmitter. The receiver must be switched o.

 Select dog A using the button on the transmitter.

 Approach the low area of the transmitter where the magnet is located until coming close to the

indicator located on the receiver (see the picture on the page 8), hold for 5 second, the receiver LED

indicator will ash four times in green and red simultaneously indicating the receiver is in

programming mode.

 Move your transmitter away and press the tone signal button on the transmitter. A beep sound is

emitted; the receiver is then synchronized with the transmitter.

 Select dog B using the button on the transmitter and proceed in the same way (applicable

when programming additional receiver for second dog).

IMPORTANT: Before the programming make sure no other person is using his d-control or

other products from the Dogtrace range close by: your receiver could accidentally record

the code of his transmitter.

Transmitter - button functions

The d–control 200 transmitter is designed to operate with two separate receivers (dog A and dog B).

The selected level of stimulations can be dierent for each receiver.

Button - Tone signal

The receiver emits a beeping noise when a "Tone button" is pressed. If the button is not released after

10 seconds, the tone will automatically turn o. While pressing, an indicator of the radio transmission

will appear on the LCD display of the transmitter; the indicator light on the receiver goes from ashing

green to permanent green for as long as the button is pressed.

Button - Continuous stimulation

Pressing the "Stimulation button" gives continuous electric stimulation transmitted by the two contact

points located on the receiver as long as the button is pushed. If the button is not released after 4

seconds, the stimulation will automatically turn o as a safety feature. The receiver will be ready to be

reactivated once the button has been released. While pressing, an indicator of the radio transmission

will appear on the LCD display of the transmitter; the indicator light on the receiver goes from ashing

green to permanent red for as long as the button is pressed.

Button - Booster

Pressing the "Booster button" gives continuous electric stimulation transmitted by the two contact

points located on the receiver as long as the button is pushed. If the button is not released after 4

seconds, the stimulation will automatically turn o as a safety feature. The receiver will be ready to be

reactivated once the button has been released. While pressing, an indicator of the radio transmission

will appear on the LCD display of the transmitter; the indicator light on the receiver goes from ashing

green to permanent red. You can set the level of the Booster stimulation by 0-5 intensity levels higher than

the level you are using on the "Stimulation button". As a result, you do not need to press the

button.

Programming the "Booster button":

 press the selection button for approximately 5 seconds until the level of stimulation ashes

on the LCD display.

 press the or button to increase or decrease the level of stimulations (0-5).

 press the selection button to conrm the level selected.

 select dog B using the button on the transmitter and proceed in the same way (applicable when

programming "Booster function" for the second receiver).

Up/Down control buttons

The control buttons are used for quick adjustment of the stimulation level of the receiver. The selected

intensity level is shown on the LCD display. There are 20 stimulation levels with 0 being the lowest and

19 being the highest. When any button is pressed the LCD display lights up for three seconds.

Dog selection buttons

The control buttons A and B are used for quick dog selection when using the device for training two

dogs simultaneously. It is possible to set dierent level of stimulation for each dog.

How to check that your d–control works correctly

You can check anytime that your d-control is operating

correctly.

 Before doing so, make sure that the receiver is switched

o.

 Place the test discharge lamp in contact with each of the

contact points as shown in the picture.

 Switch on the transmitter and receiver.

 Press the stimulation button and modify the level of

intensity of the stimulations: the test lamp will come on

with more or less intensity according to the selected

intensity level. Location of the test lamp attachment

Using d–control training collar in winter

When using d-control in winter, please keep in mind:

 Low humidity – causes less skin conductivity. It is necessary to provide better conductivity

between the electrodes of the receiver and the dog‘s skin. This can be achieved by lubricating the

dog’s skin in the touch points of contact points with Vaseline, baby oil, hand lotion, etc.

 Heavier dog’s coat – it is necessary to tighten the collar so that the permanent contact with the

dog‘s skin is ensured. If the coat is too thick, it is recommended to choose a longer type of contact

points.

 Battery properties change – temperatures below 0 °C slow down chemical reactions in batteries.

To ensure a performance of repetitive stimulations (especially of higher levels), it is recommended

to insert a new battery into the receiver for the winter time. During the training, observe

continuously dog‘s reactions and increase the stimulation level as needed.

The training commands are transmitted to the receiver by radio waves. The range of the d-control 200

mini is approximately 200 metres depending on the geographic conditions. The transmitter range may

vary depending on the way you use your transmitter, hold the transmitter away from your body and

avoid touching the front part of the transmitter where the antenna is located.

FITTING THE COLLAR

The receiver needs to be very snug around the dog‘s neck to work properly. A loose t can allow the

receiver to move around on the dog‘s neck. The collar must be just tight enough to allow the contact

points to make good contact on your dog‘s skin. You may need to trim the hair in the area of the

contact points or switch to the longer contact points to ensure consistent contact. This can directly

aect the performance of the collar unit and whether or not the dog will receive the stimulation

impulses. A loose collar can also result in skin irritations. The collar should be tight enough to t two

ngers between the collar and your dog‘s neck, but not so tight that it restricts your dog‘s breathing.

Getting the best results

TIP By placing the receiver on your dog’s neck laterally, you will extend the range of transmission.

Training tips

 The trainer’s elementary knowledge in dog training is the prerequisite for using the training collar.

Do not hesitate to contact a professional trainer for any further advice.

 You can start using the collar with dogs of 6 months of age who has undergone the basic training

and are familiar with basic obedience commands including "sit", "down", "stay" etc.

 Find proper intensity level for each dog before use. It is very important to set the correct intensity

level on your unit before beginning your training sessions to provide the appropriate level of

stimulation and avoid over-stimulating your dog.

 Eliminate one misbehaviour or teach one obedience command at a time.

 Be consistent. Give your dog a tone or stimulation with each misbehaviour.

 After a command is successfully executed, you should always reward or encourage your dog.

 To teach your dog a reliable recall start training your dog using a long dog tracking lead.

 Your dog will have to get used to the collar; let the dog wear the collar for a few days, but do not

use it so that your pet does not discover the connection with its attachment and effects.

 Affirmative and efficient training requires some time: don't hurry!

 Select a well-known environment your dog is used to.

 Choose the right moment to press the stimulation button.

 We recommend not to use the electronic training collar with aggressive-tempered dogs and with

dogs with health problems.

Caution

It is important to keep the device clean. Clean the contact points regularly, avoid using any detergent

that contains strong chemicals. To clean your d-control use a soft cloth moistened with water and

neutral detergent. The transmitter is not waterproof, so use caution when operating your device in wet

Maintenance

 Keep away from children.

 Do not leave the device in or around a high temperature heat source.

 Check the receiver for proper tightness of screws and seal before each use.

 Battery of the receiver needs to be replaced in every two years, check the battery power level

before each use.

 The transmitter is not waterproof, so use caution when operating your device in wet conditions,

water can cause irreversible damage to your device.

 Do not use the electronic training collar for dogs under 6 months of age.

 Do not use the electronic training collar for pregnant or nursing bitches.

 Do not use the electronic training collar for dogs with health problems particularly heart disease,

unless the use has been approved by veterinarian.

 Do not use the electronic training collar for dogs that cannot respond appropriately due to injury,

illness, senility or age.

 We recommend that your dog has a preventive medical check before using the electronic training

collar.

 We recommend not to use the electronic training collar with aggressive-tempered dogs.

 Check the contact area regularly for signs of neck irritations, to prevent neck irritations, the collar

should never be worn for more than 12 hours per day. If a rash or sore is found, do not use the collar

until the skin has healed.

 Never connect a leash to the electronic collar; this could cause excessive pressure on the contact

points. Always use a separate leash, do not put pressure on the electronic collar.

Troubleshooting

 If your device seems to operate improperly, read this manual again, check the receiver battery and

replace it if necessary.

 Try to initialize the receiver by removing the battery from the battery holder in the receiver, then

use a metal tool (e.g. a screwdriver, scissors, etc.) and short-circuit both contacts of battery holder

for approximately two seconds, and then put the battery back in its place observing the correct

polarity. A beep sound is emitted indicating the correct installation of the battery.

 If the problem still persists, try to program the transmitter

with receiver again according to the instructions in this

manual.

 If the problem still persists, contact the dealer.

Short-circuit of the receiver

TIP While using the device, it is recommended to check periodically

that screws in the receiver lid are tightened correctly.

conditions, water can cause irreversible damage to your transmitter. The receiver is waterproof. The

receiver case is provided with a seal that forms a waterproof barrier between the lid and main housing

of the case. If the seal is loose, out of alignment or twisted, it will compromise the waterproof integrity

of the case. Lubricating the seal with a thin layer of silicone grease will increase its lifespan. We

recommend replacing the seal in the receiver every year. It is recommended to remove the battery

from the receiver, if the device will not be in use for a month or longer.

TRANSMITTER

Weight ...............................................64 grams (without battery)

Range ................................................approx. 200 meters in the free area

Power supply .........................................lithium CR2 3V battery

Battery life ............................................6–12 months, based on usage

Frequency ............................................869, 525 MHz

Maximum transmitted power .........................10 mW

Antenna ..............................................integrated

Watertightness .......................................not waterproof

Radio communication safety and coding ..............by microcontroller

Number stimulation levels ............................20

Operating temperature ...............................–10 °C to + 50 °C

Dimensions ...........................................110 × 52 × 29 mm

RECEIVER

Weight ...............................................44 grams (without the strap and the battery)

Power supply .........................................lithium CR2 3V battery

Battery life ............................................6 months, based on usage

Frequency ............................................869, 525 MHz

Antenna ..............................................Integrated

Watertightness .......................................waterproof

Radio communication safety and coding ..............by microcontroller

Operating temperature ............................... –10 °C to + 50 °C

Collar .................................................adjustable to neck sizes from 20 to 70 cm

Dimensions ...........................................61 × 40 × 31 mm

Technical specications

VNT electronics Ltd. provides a 2-year warranty on the DOGtraceTM product with respect to defects in

material and workmanship under normal use and service from the date of the original purchase.

The limited warranty does not cover the following:

 batteries

 straps

 damage resulting from misuse, accident, modication or alteration to hardware or software,

tampering, unsuitable physical or operating environment beyond product specications, improper

maintenance, or failure caused by a product for which VNT electronics Ltd. is not responsible.

1. The warranty period commences on the date of purchase. The sales receipt or your purchase

invoice showing the date of purchase of the Product, showing the serial number and date of

purchase of the Product, is the proof of the date of purchase.

2. Within the warranty period, VNT electronics Ltd. will, at no additional charge; perform repair or

replacement of defects in workmanship or parts covered by this warranty.

3. The warranty does not cover damage resulting from:

a) transportation, fall, weather, extreme temperatures, improper use, mishandling or negligence after

the purchase of the Product

b) natural disaster (wind, earthquake, lightning storm etc.)

c) maintenance or misuse other than in accordance with the instructions provided by

VNT electronics Ltd. in relation to the Product

d) modication by a party not authorized by VNT electronics Ltd.

4. The warranty provided only applies to the Product purchased from ocial authorized dealer.

Warranty Terms and Conditions

5. We require that all items being sent for repair must be clean. Items deemed insuciently clean will

be returned to the customer unrepaired. Please do not include the strap or any other accessories if not

subject to warranty.

6. Other rights and liabilities of the manufacturer and claimants are based on relevant general

obligatory legal regulations of the country where the product was sold.

The content of this user guide may be subject to change without prior notice.

Manufacturer: VNT electronics s.r.o.

Smetanovo náměstí 104

570 01 Litomyšl

Czech Republic

Phone: +420 733 121 890

www.dogtrace.com

Dealer:

Copying of this user guide is strictly prohibited without the prior written consent of VNT electronics Ltd.

Version 2016-4-21 / EN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dogtrace d-control 202 mini in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dogtrace d-control 202 mini Manual

Product: