67777
4
Zoom out
Zoom in
Previous page
1/16
Next page
Wiring
Power connections
Ground Terminal ( GND )
Remote terminal ( REM )
Use only three 30 ampere
ATC blade type fuses.
4
Power terminal ( +12V)
Connect the battery cable from the fuse holder to
the +12 Volt terminal on the amplifier.
Be sure to use a rubber grommet or a plastic
insulating tube where the cable passes the firewall
or other places when it can easily be jammed.
Use ty-wraps to secure to existing cables in the
engine compartment.
DLS FH1 or
FH2B
fuse holder
Connect to a good chassis ground. The ground
connection should be clean, unpainted metal to
provide a good electrical connection. Use a wire
brush, a scraper or a piece of an abrasive sheet to
clean the metal. Use a lock washer or two to secure
contact. Protect with silicon grease or by paint
applied afterwards.
Power
(Green)
Protect
(Red)
Power Light / Protect light
The power light (green ) comes on when
the amplifier is turned on.
The protect light ( red ) comes on
when the amplifier shuts down from
DC offset, overheating, or a short
circuit ( speaker failure)
Fuses
For RCA cable signal input:
Set the input selector switch to position ”Low level”.
Connect the radio power antenna lead = remote
turn on/off from the car stereo to the amplifier
remote connection. This turns on the amplifier
whenever the car stereo is turned on.
You can either use the built in remote cable in the
RCA cable itself or use a separate cable.
Sometimes a small disturbance may enter the
amplifier coming from the remote voltage , through
the built in remote wire and into the RCA cable.
Thus we recommend to use a separate remote wire
and run the RCA lead separate from remote wire,
power cables and speaker cables.
Insert the cable directly into the amplifier terminal.
If there is no remote voltage available from the ste-
reo, you must connect to the ignition key through
the radio or any accessories fuse.
Set the ”High level auto
start” switch to position
OUT.
For High Level input:
Set the input selector switch to position ”High level”.
We recommend you to connect the remote wire as
described above. The amplifier will produce soft
on / soft off operation this way. If you use a remote
wire, set the switch ”High level auto start” to posi-
tion OUT.
In the case that there is no remote voltage available
from the car stereo, or you want to simplify the in-
stallation, the amplifier can be turned on/ turned
off by the high level input voltage. This is done
when the ”High level auto start” switch is set to IN
- position.
RA50
DLS
Connect with
ring terminal to
battery + terminal
Connect with ring
terminal to
chassis ground
Connect to head
unit remote start
terminal or power
antenna lead
Connect the fuse holder as close to the vehicle
battery + as possible, using AWG 4 = 21 mm
2
or
heavier cable. Use ring crimp terminal cable to
connect to battery +. Apply silicon grease to the
fuse to prevent corrosion.
Use an 80 A fuse for cable
4AWG (21 mm
2
).
30 A
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS RA 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS RA 50 in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info