163877
8
Zoom out
Zoom in
Previous page
1/26
Next page
The LP-filter on the rear channels is used when
you run a 2-way or 3-way speaker system with
active crossover. It will allow low frequencies only
and blocks higher frequencies. The filter can be
switched in and out.
The normal frequency range is from 0,3 to 4 kHz.
With the LP x10 switch, under the bottom plate,
you can change the filter frequency range from the
normal to 3 - 40 kHz. A normal x-over setting is 3-4
kHz when used for active crossover in a 2-way sys-
tem.
If you run a 3-way system on the amplifier you can
use this filter for active crossover between midbass
and midrange speakers. A typical setting is 400 Hz.
The sub channel is made only for subwoofer use
and has a variable LP-filter. A normal setting for the
LP-filter is 60-80 Hz.
FRONT SPEAKERS
+LEFT- +RIGHT-
REAR SPEAKERS
+LEFT- +RIGHT-
SIGNAL INPUTS
FRONT REAR
LEFT RIGHT LEFT RIGHT
3,5V
7V 0,2V
3,5V
7V 0,2V
LEVEL
x20 change
by bottom switch
240
80 400
Hz
OUT
IN
HP-filter
240
80 400
Hz
OUT
IN
HP-filter
2
0,3 4
kHz
OUT
IN
LP-filter
LEVEL
x10 change
by bottom switch
Lowpass filter on rear channels
x10 change
by bottom switch
2
0,3 4
kHz
OUT
IN
LP-filter
Amplifier front
x 20
x 1
HP
x 1
x 10
LP
Input
Front Rear
Input
Sub
Front
input to
rear & sub
Rear
input to
sub
Sub input
from rear
Sub input
separate
LP x10 swith under the bottom plate
Filters on sub
channel
Crossovers / filters on A7
DLS A7 amplifier include highpass filter (HP),
lowpass filter (LP). On the two front channels the
HP-filter can be switched between two different
frequency ranges, likewise for the LP-filter on the
rear channels.
The slope of the HP-filter is
12 dB / octave.
The filter can be switched
off if you want to run the
amplifier in full range mode.
Or use as a HP-filter for
tweeters if you want to run
a 2-way speaker system
with active crossover. The
HP x20 switch under the
bottom plate changes the
filters frequency range from
the normal 80-400 Hz to
1600 - 8000 Hz. A normal
setting is 3-5 kHz.
If you run a 3-way system
on the amplifier you can use
this filter for active cross-
over between midbass and
midrange speakers, a
typical setting is 400 Hz.
Highpass filter on front channels
Highpass filter on rear channels
8
x20 change
by bottom switch
240
80 400
Hz
OUT
IN
HP-filter
Amplifier front
x 20
x 1
HP
x 1
x 10
LP
Input
Front Rear
Input
Sub
Front
input to
rear & sub
Rear
input to
sub
Sub input
from rear
Sub input
separate
This HP-filter is normally
used as a high pass filter
blocking very low frequencies
from reaching the speakers.
It is mostly used at say 80 Hz
to protect small speakers
( like 6 inch and smaller ) from
deep bass.
The slope of the HP-filter is
12 dB / octave.
The filter can be switched off
if you want to run the amplifier
in full range mode.
240
80 400
Hz
OUT
IN
HP-filter
ULTIMATE A7
Lowpass
90
50 125
Hz
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS a7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS a7 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info