163874
4
Zoom out
Zoom in
Previous page
1/26
Next page
Connect the fuse holder as close to the vehicle battery
+ as possible, using AWG 5 = 16 mm
2
or heavier cable
(see table on page 2). Use ring crimp terminal cable
to connect to battery +. Apply silicon grease to the
fuse to prevent corrosion.
Connect the battery cable to the +12 Volt terminal
on the amplifier. Model A2, A5 and A7 accepts AWG
4 = 21 mm
2
direct into the terminal. Be sure to use a
rubber grommet or a plastic insulating tube where
the cable passes the firewall or other places where
it can easily be jammed.
Use wire ties to secure to existing cables in the
engine compartment.
Wiring
Power, remote and fan terminals
ULTIMATE A-series
Power terminal for A2, A5, A7
Remote terminal ( REM )
For RCA cable signal input:
Connect the radio power antenna lead = remote
turn on/off from the head unit to the amplifier remote
connection. This turns on the amplifier whenever
the car stereo is turned on.
You can either use the built in remote cable in the
RCA cable itself, or use a separate cable.
Sometimes a small disturbance may enter the
amplifier coming from the remote voltage, through
the built in remote wire and into the RCA cable.
Thus we recommend to use a separate remote wire
and run the RCA lead separate from remote wire,
power cables and speaker cables.
You can insert the cable directly into the amplifier
terminal. If there is no remote voltage available from
the stereo, you must connect to the ignition key,
through the radio, or any accessories fuse.
4
DLS FH1B or
FH2B
fuse holder
Battery 12V
DLS
POWER IN
BATT+ REMOTE GND
Power terminal for A3, A4 & A6
These models have double DC inputs. The termin-
als are internally connected so it´s enough to
connect just one of them. If you want to reduce the
voltage drop to the amplifier, use both inputs. The
extra DC input can also be used for the connection
of a Power Capacitor or an extra battery. See the
example above. These amplifiers requires a
powerful fuse holder like the FH2B with an ANL 150
Amp fuse (when using 2AWG / 33 mm
2
power
cable).
Ground Terminal ( GND )
POWER IN
BATT+ REMOTE GND
FM1 107,3
Fuses
Use only ATC blade type
fuses. Make sure to replace
with the same value. The
value is printed above the
fuse holders. DLS A4 has no
internal fuses, use an
external fuse instead.
POWER IN
BATT+ REMOTE GND
Fan terminal
DLS A3, A4, A5, A6 and A7 has a fan
output terminal. On A3, A4 and A6
the terminal is combined with the
extra DC-terminal. The output is
electronically controlled and starts if
the amplifiers is overheated. The ter-
minal is marked "FAN”.
Use a 12 volt DC fan.The speed of
the fan increases when the tempera-
ture rises. Direct the fan towards the
amplifier cooling ribs. Full speed is
obtained at 70 degrees C. NOTE!
Maximum load on the FAN terminal
is 0,5 Amp.
Power
capacitor
Fuse
150 A
Fan12 V
To remote
on head unit
POWER IN
BAT+ REM GND
POWER IN /POWER CAP
GND FAN OUT POS+
PROTECT
POWER
+
Battery
12 volt
Connect to a good chassis ground. The ground
connection should be clean, unpainted metal to prov-
ide a good electrical connection. Use a wire brush,
a scraper or a piece of an abrasive sheet to clean
the metal. Use a lock washer or two to secure
contact. Protect with silicon grease or by paint
applied afterwards.
Fan 12 V
FAN
- +
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS a2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS a2 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info