Manual DKN Ecorun (page 117 of 122) (English, German, Dutch, French, Italian, Spanish)

569915

117

Zoom out

Zoom in

1/122

117

Code Description Processing

E01

Communication error. The control board and

computer are not communicating correctly.

The machine stops and goes into fault status, computer shows “E1”, and the alarm beeps three times.

Possible causes: check all the connection points between the console and controller. Make sure all plugs

are well connected. Check all the wires for damage. If this fails, change the connector wires.

E02

Erratic motor cable connection

Start and stop fault status. The computer beeps 9 times and shows “E2”. Treadmill goes into the ready

mode and restarts. Possible causes: low power or voltage, or faulty controller. Check all motor wires for

correct connection.

E03

Speed sensor error.

Stops and go into fault status. Computer shows “E03”. Other areas show blank. After 10 seconds the

machine will go into ready mode, and can be restarted.

Possible causes: the computer is not receiving motor speed sensor feedback for more than 3 seconds:

check sensor plug and motor connection wires. Check the controller.

E04

Incline motor error

Check if incline motor sensor wire and AC wire are well connected. After checking press the button on

controller to reset the incline motor adjustment.

E05

Over-current protection.

Stops and goes into fault status, computer shows “E05”. Other areas show blank. After 10 seconds the

machine will go into ready mode, and can be restarted.

Possible causes: system encounters overvoltage and goes to self-preservation. Moving parts may be

blocked. Check and adjust the machine and restart. Check motor or controller for burning smell. If so,

change motor and/or controller. Check whether the power voltage is too low or not to the standard and

retest with the correct voltage.

E06

Controller self-check error.

Computer shows "E06". Possible causes: the controller wires are not connected well, check and

reconnect or change. After checking press the button on controller to reset the system.

E07

EPROM (Data memory error)

Computer shows“E08”. Possible causes: the controller wires are not connected well, check and

reconnect or change EPROM IC.

The platform slows down after s few seconds and stops why? Submitted on 16-1-2021 at 15:53
Reply Report abuse
The treadmill shows error E2 and won't run. I have checked to see if there are any loose wires, but they seem to be OK. When turned on and Start pressed, there are a few clicks before it puts up the E2 message. Submitted on 4-9-2020 at 14:58
Reply Report abuse
The treadmill is showing E1, and it's failing to run Submitted on 3-10-2019 at 12:24
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DKN Ecorun in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DKN Ecorun Manual

Product: