612045
26
Zoom out
Zoom in
Previous page
1/32
Next page
Spreading Wings S900
User Manual
26
©
2014 DJI. All Rights Reserved.
Remounting the Landing Gear Servo
Remounting servos is not recommended as they are pre-installed.
Instructions
1. Connect the left servo cable to the “L” port of the landing gear control board.
2. Connect the right servo cable to the “R” port of the landing gear control board.
3. Press and hold the SET button using a pin then power on. You will see a yellow LED beside the SET button
ashing quickly. Wait as servos complete position initialization.
4. Make sure the arm connecting to the servo is parallel to the link as shown in the following diagram.
5. Assemble the left and right servos to the left (between M3, M4) and the right (between M5, M6) parts of the
landing gear. Power off.
Recalibrating Servo Travel
Instructions
1. Keep your hands away from all moving parts.
2. Ensure the “R”, “L” and “IN” connections are correct.
3. Keep the whole aircraft off of the ground during calibration, as landing gear will move.
4. Press and hold the SET button using a pin while powering on, then release. An LED will flash yellow
quickly. Press the SET button again. Auto calibration will begin and the LED will ash yellow slowly. DO
NOT obstruct any moving parts during auto calibration.
5. During calibration, the left landing gear will raise and lower, followed by the right landing gear.
6. After calibration, both the left and right landing gears will be lowered and the LED will display a solid green
light. This indicates that the landing gear is working properly.
If the LED is solid yellow after calibration, a problem has occurred. Carry out the instructions in
“Remounting the Landing Gear Servo” then try again.
Avoid obstructions during calibration. If the landing gear was obstructed, recalibration will be
required, per the above steps.
If the “R” and “L” servo cables are reversed, travel will not be measured correctly. Fix the
connections and recalibrate the landing gear using the above steps.
Landing gear travel has been pre-calibrated. Mechanical adjustment of the gear travel is not
recommended.
After Installation
Servo
Connecting arm
Link
R
L
IN
To left servo
To receiver channel
(To F1 port if use A2)
SET Button
LED
To right servo
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DJI SPREADING WINGS S900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DJI SPREADING WINGS S900 in the language / languages: English as an attachment in your email.

The manual is 6,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info