499507
39
Zoom out
Zoom in
Previous page
1/44
Next page
- 39 -
0DT829 15/10/2012
7. TROUBLESHOOTING
When working with electrical or electronic controls, make sure that the power source has been locked
out and tagged according to approved local electrical codes.
The following instructions are intended only for qualied personnel, authorized to operate under the
owners responsibility. Safety rules and local codes must be applied also when our instructions are not
specifying it in each single operation.
For repair or replacement only Ditec Entrematic original spare parts must be used.
DANGER
WARNING
COMMAND TROUBLE VERIFY

curtain position
The curtain and motor do
not move
Mains power failure or fuses F1, F2, F3
The stop is activated (led “Stop” of the keyboard ON)
The motor is connected to wrong terminals and/or Dip-switch
is in wrong position (see page 8)
The opening (A) and closing (C) limit switches are activated
(led 11 and 12 ON)
Motor with thermal switch activated (led 11 and 12 ON)
One of the power devices is faulty (control unit, motor, motor
cabling, etc.)
The motor turns in the
opposite direction
Reverse the two phases of the mains power supply
Opening command at
closed curtain
The motor does not move The opening command is not correctly connected or it is faulty
(led IN does not switch ON).
Safety device activated (led “Stop” ashing on the keyboard
and led SA xed ON) with bridge SO closed.
The opening limit switch (A) is activated
Closure command always activated (led IN always ON).
Closure command at
opened curtain
The motor does not move The closing command is not correctly connected or is faulty
(led IN does not switch ON).
Safety device activated (led “Stop” ashing on the keyboard
and led SA xed ON).
The closing limit switch (C) is activated (led 11 xed in ON).
Opening command always activated (led IN always ON).
Self-test of the safety device failed (led Stop on the keyboard
OFF and led SA ashing)
Activation of the stop
during a door cycle
The motor does not stop The stop command is faulty or is not correctly connected (led
stop on the keyboard never in ON and led SA not ashing)
The motor stops with
delay
The motor brake worn-out or faulty
Activation of one safety
device during closing
The motor movement is
not reversed
The safety device is faulty or is not correctly connected (led
Stop on the keyboard OFF and led SA never ashing)
The motor movement
stops (the door doesn’t
open completely)
Input 17 closed to 0 (led 17 OFF)
Door open with automatic
closure activated
The door does not close
automatically after closing
time TC
The automatic closure enable signal has not been carried out
properly (connection 1-2)
Opening command always activated (led IN always ON).
Self-test of the safety device failed (led Stop on the keyboard
OFF and led SA ashing)
During operation The curtain doesn't stop
at the limitswitch
The limit switch contact is short-circuited (led 11 or led 12
always OFF)
• A mechanical fault in the limit switch (led 11 or led 12 always OFF)
The motor brake worn-out or faulty or brake (led 11 or led 12
always OFF)
The curtain doesn't
stop regularly at the
limitswitch
• Dip-switch 5 in OFF
• Fuse F5 fault
NB for inverter control unit 47E see also at page 37.
EN
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DITEC Traffic CM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DITEC Traffic CM in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info