Manual DITEC BOX3EH (page 11 of 32) (English, German, French, Italian, Portuguese, Spanish)

749190

Zoom out

Zoom in

1/32

11 BOX - IP1529

MACHINERY DIRECTIVE

Pursuant to Machine Directive (98/37/EC) the installer who mo-

torises a door or gate has the same obligations as a machine

manufacturer and shall:

- prepare technical documentation containing the documents

indicated on Schedule V of the Machine Directive;

(The technical documentation shall be kept and placed at

the disposal of competent national authorities for at least ten

years starting on the date of manufacture of the motorised

door);

- draw up the EC declaration of conformity according to Sche-

dule II-A of the Machine Directive;

- afx the CE mark on the motorised door pursuant to para.

1.7.3 of Schedule I of the Machine Directive.

For more details, refer to the “Guidelines for producing technical

documentation” available on Internet at the following address:

www.ditec.it

OPERATING INSTRUCTIONS

Service class: 3 (minimum 30 cycles a day for 10 years or 60

cycles a day for 5 years)

Use: FREQUENT (for multi-family entrances or small condomi-

niums with frequent car or pedestrian transit)

- The operating performance specications refer to the re-

commended weight (about 2/3 of maximum allowed weight).

Use with maximum allowed weight could reduce the above

performance specications.

- The service class, operating times and number of conse-

cutive cycles are merely approximate. These have been

statistically determined in average conditions of use and

are not certain for each single case. They refer to the pe-

riod when the product operates without the need for special

maintenance.

- Each automatic entrance features variable factors such as:

friction, balancing and environmental conditions that can

substantially change both the duration and operating quality

of the automatic entrance or part of its components (including

automatic system). It is up to the installer to adopt adequate

safety coefcients for each single installation.

MANUFACTURER’S DECLARATION

(Directive 98/37/EC, Schedule II, part B)

Manufacturer: DITEC S.p.A.

Address: via Mons. Ban, 3 - 20142

Caronno P.lla (VA) - ITALY

Declares that the automatic system for spring balanced up and

over doors of the BOX series:

- is manufactured to be incorporated into a machine or to be

assembled with other machines to make a machine considered

by Directive 98/37/EC;

- is in conformity with the conditions of the following other EC

directives:

Electromagnetic compatibility directive 89/336/EEC;

Low-voltage directive 73/23/EEC;

and further certies that the machine shall not be commissioned

until the machine into which it is to be incorporated or of which

it is to become a component part has been identied and has

been declared in conformity with the conditions of the Directive

98/37/EC and the transposing national legislation.

Caronno Pertusella, Fermo Bressanini

09-04-2001 (President)

GENERAL SAFETY PRECAUTIONS

This installation manual is intended for professionally

competent personnel only.

Installation, electrical connections and adjustments must be

performed in accordance with Good Working Methods and in

compliance with applicable regulations. Before installing the

product, carefully read the instructions. Bad installation could

be hazardous.

The packaging materials (plastic, polystyrene, etc.) should not

be discarded in the environment or left within reach of children,

as these are a potential source of hazard. Before installing the

product, make sure it is in perfect condition.

Do not install the product in an explosive environment and atmo-

sphere: gas or inammable fumes are a serious hazard risk.

Before installing the motors, make all structural changes relating

t o safety clearances and protection or segregation of all areas

where there is risk of being crushed, cut or dragged, and danger

areas in general.

Make sure the existing structure is up to standard in terms of

strength and stability.

The motor manufacturer is not responsible for failure to use

Good Working Methods in building the frames to be motorised

or for any deformation occurring during use.

The safety devices (photocells, safety edges, emergency stops,

etc.) must be installed taking into account: applicable laws and

directives, Good Working Methods, installation premises, system

operating logic and the forces developed by the motorised door

or gate.

The safety devices must protect any areas where the risk exists

of being crushed, cut or gragged, or where there are any other

risks generated by the motorised door or gate. Apply hazard

area notices required by applicable regulations.

Each installation must clearly show the identication details of

the motorised door or gate.

Before making power connections, make sure the plate

details correspond to those of the power mains.

Fit an omnipolar disconnection switch with a contact opening

gap of at least 3 mm. Make sure an adequate residual current

circuit breaker and overcurrent cutout are tted upstream of

the electrical system. When necessary, connect the motorised

door or gate to a reliable earth system made in accordance with

applicable safety regulations. During installation, maintenance

and repair, interrupt the power supply before opening the lid to

access the electrical parts.

To handle electronic parts, wear earthed antistatic con-

ductive bracelets.

The motor manufacturer declines all responsibility in the event

of component parts being tted that are not compatible with the

safe an correct operation.

For repairs or replacements of products only original spare parts

must be used.

The installer shall provide all information relating to automatic,

manual and emergency operation of the motorised door or gate,

and provide the user with operating instructions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of DITEC BOX3EH in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

DITEC BOX3EH Manual

Product: