320873
14
Zoom out
Zoom in
Previous page
1/29
Next page
14
4 Operation
This is how to attach the nozzles:
1. Switch off the vacuum cleaner and pull the plug from the mains socket.
2. Pull the attached nozzle from the telescopic tube.
3. Put the desired nozzle onto the bottom end of the telescopic tube (Fig. 8/1) or if necessary directly onto the
handle (Fig. 8/2).
4. Attach the nozzles no longer required to the accessory bracket, as far as this is possible (Fig. 9).
4Operation
4.1 Before starting
vacuum-cleaning
.
4.2 Vacuum cleaning 1. Attach the desired nozzle ZChapter 3.2, "Assembly" or ZChapter 3.3, "Using further nozzles (accessories)".
2. Pull out the cord by the plug up to the yellow mark (Fig. 10/1).
3. Switch on the cylinder vacuum cleaner with the on/off switch (Fig. 11/1).
4. Set the nozzle switch to "carpet" or "hard floor" (Fig. 12/1) according to the floor to be cleaned:
- Hard floor (Fig. 12/a)
Laminate, tiles, PVC, etc.
- Carpet (Fig. 12/b)
Short- and deep-pile carpets, rugs, etc.
5. When working with the cylinder vacuum cleaner, pull if after you like a sleigh.
WARNING:
Danger of injury! Only assemble the appliance if it is not connected to the power supply. Otherwise the machine
might start up and parts of your body, hair or pieces of clothing might be sucked in.
ATTENTION:
Use only intact nozzles. Damaged nozzles may scratch or damage surfaces and objects.
ATTENTION:
Using the cylinder vacuum cleaner without a nozzle attached increases the danger of accidentally sucking in objects.
1
2
8
ab
9
WARNING:
Danger of injury! A damaged appliance must never be used. Check the cylinder vacuum cleaner and the power
cord before each use.
ATTENTION:
Only use the cylinder vacuum cleaner with all filters intact, in dry condition and correctly placed. Make sure that the
openings of the vacuum cleaner are not clogged.or obstructed. Otherwise the vacuum cleaner might be damaged.
ATTENTION:
Check the requirements of your floorings before using the vacuum cleaner. Follow the recommendations of the
flooring manufacturers.
NOTE:
Your cylinder vacuum cleaner is equipped with a safety switch to prevent overheating. It automatically cuts off
the power supply if the motor is overheated. If this happens switch off the cylinder vacuum cleaner and
disconnect it from the mains. Remove the cause of the overheating. Wait for about 45 minutes. After it has
cooled off, you may use the cylinder vacuum cleaner again.
WARNING:
Danger of electric shock! If the red marking (Fig. 10/2) is visible, retract the cord by pressing the retract button
(Fig. 11/2) to pull in the cable up to the yellow mark again. Otherwise the cord might break.
WARNING:
Danger of tripping! Pull out the power cord only as far as necessary. After vacuuming, roll up the power cord
again by pressing the cable retract button (Fig. 11/2) immediately..
NOTE:
With the bypass vent (Fig. 13/1) you can quickly reduce suction power if less suction is needed, e.g. to release
objects accidentally sucked in.
1
2
10
11
b
a
1
12
1
13
V8.book Seite 14 Mittwoch, 6. April 2011 10:09 10
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dirt Devil m 5021 0 infinity v8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dirt Devil m 5021 0 infinity v8 in the language / languages: English, German, Dutch, French, Italian, Turkish, Spanish as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info