798315
14
Zoom out
Zoom in
Previous page
1/36
Next page
EN-2 452115.66.26 FD 9404
WPM Econ5
English
1 Important Information
During commissioning, observe the respective national
safety regulations and the applicable VDE safety
regulations, particularly VDE 0100, as well as the technical
connection requirements of the utility companies (EVU) and
network operators!
The heat pump manager should only be operated in dry
rooms with temperatures ranging between 0 °C and 35 °C.
Ensure that no condensation forms on the device.
All sensor connection leads can be extended in accordance
with the electrical documentation to up to 50 m with
0.75 mm² Cu cables with routing type B2 and an ambient
temperature of 35 °C. Sensor leads should not be installed
next to power cables.
To ensure that the frost protection function of the heat pump
works properly, the heat pump controller must remain
connected to the power supply and the flow must be
maintained through the heat pump at all times.
The switching contacts of the output relay are interference-
suppressed. Therefore, depending on the internal
resistance of the measuring instrument, a voltage can also
be measured when the contacts are open. However, this will
be much lower than the line voltage.
Terminals J1 to J11, J24 - J26 and the terminal strip X3 of
the heating controller N1 are connected to a low voltage
supply. If, due to a wiring error, the line voltage is mistakenly
connected to these terminals, the heat pump manager will
be destroyed.
2 Heat Pump Manager: Scope of Supply
The heat pump manager is available in three versions.
Integrated in the heat pump casing
Heat pump manager for wall mounting
for a heat pump heating system
Heat pump manager for wall mounting
for a heat pump system for heating.
The scope of supply of the wall-mounted heat pump manager
includes:
Heat pump manager with casing
3 dowels (6 mm) with screws for wall mounting
Sensor for the outside temperature, demand sensor R2.2
and with domestic hot water cylinder R3
Operator's manual and operating instructions for users
Installation and commissioning instructions for technicians
Electrical documentation
3 Assembly
3.1 Attaching the wall-mounted heat pump manager (heating)
The controller is attached to the wall with the 3 screws and
dowels (6 mm) included in the scope of supply. The following
installation procedure must be followed to avoid soiling or
damaging the controller:
Mount the dowels for the upper fastening eyelet at operator
level.
Screw the screw into the dowel so that the controller can be
mounted.
Mount the controller by the upper fastening eyelet.
Mark the position of the side drill-holes.
Unhook the controller.
Mount the dowels for the side drill-holes.
Remount the controller at the top and tighten the screws.
Fig. 3.1: Dimensions of the wall-mounted heat pump manager (heating)


14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex WPM Econ5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex WPM Econ5 in the language / languages: English, German, French as an attachment in your email.

The manual is 1.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info