706539
7
Zoom out
Zoom in
Previous page
1/41
Next page
Controls: See Fig. 2 & 3
Icon Display Function Description
A -
Power /
Standby
Press once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless the product
has been plugged out, in which case it will reset to factory settings)
B
Sleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5 hr to 8.0 hr before turning
off. The remaining time on the ‘SLEEP TIMER’ displays. (This icon is Green in Colour)
C
Flame Effect
‘FLAME EFFECT’ button cycles the unit sequentially through the 4 setting, LOW FLAME, HIGH FLAME,
DEMO MODE and OFF.
f1
Low
Flame
This setting will run the ame effect at a low brighness level. (The display will show F1)
f2
High
Flame
This setting will run the ame effect at a high brighness level. (The display will show F2)
fp
Demo
Mode
This setting will slowly pulse the ame effect between low and high brightness. (The display will show
FP)
-
Off
This will turn the ame effect off. If the heater is running, the display will activate and remain active to
read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.
D
Colour Theme ‘Colour Themes’ are setting which change the colour of the fuel bed there are eight different themes
Theme 1
Theme 1 is a ‘Demo Mode’ this setting will scroll throught all of the colour settings you can ‘Pause’
this demo mode by pressing the ‘Brightness Button’ / in which case the display will read
1.p
to
‘Unpause’ press the ‘Brightness Button’ / in which case display will read
1.U
2-8
Theme
2-8
Themes 2-8 are preset colours that remain static.
E
-
Bright-
ness
This button switches themes 2-8 between full brightness and half brightness. This button also interacts
with the product when set on theme as perviously described above
F
Heat
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW
and OFF. The heat setting will be indicated by an icon in the oating display see Fig. 2.
When the ame effect is ‘ON’ the oating display will turn off after 5 seconds, however if the heater is
being used independantly of the ame effect. The low heat or high heat icon will appear continuously
in the oating display.
Low Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW HEAT’ icon
and the letters ‘LO’ appearing in the display.
(This icon is Orange in Colour)
High
Heat
This icon in the oating display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH HEAT’
icon and the letters ‘HI’ appearing in the display.
(This icon is Red in Colour)
Cool
Blow
This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by the ‘COOL
BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is Blue in Colour)
- Off
This switches the heater and blower ‘OFF’, no icon will be displayed in the oating display. Note the
blower will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.
G -
Temp
Down
Press multiple times to lower the heater temperature in 1ºC increments. The lowest temperature that
can be set 5ºC.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
H - Temp Up
Press multiple times to increase the heater temperature in 1ºC increments. The highest temperature
that can be set is 37ºC.
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the
room temperature as detected by the product. If the set temperature is lower than the detected
room temperature the heater will not activate.
User Modes:
Mode Name /Discription Action (Actions cannot be input by remote control)
Change Celsius (º C) to Fahrenheit (º F)
Press both 3 Dot Button ( ) and 2 Dot ( ) on the unit and hold until beep is heard
and display flashes. (To revert back to Celsius repeat this action)
Disable/Enable Heat Options
Hold both 1 Dot Button ( ) and Flame Button ( ), on the unit, for 2 seconds, when
the heater has been disabled the display will read “--” and beep. To enble heat repeat
this action.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dimplex Wickson at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex Wickson in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish, Norwegian as an attachment in your email.

The manual is 9,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info