Manual Dimplex WI 140TUR plus (page 25 of 72) (English, German, French)

798436

Zoom out

Zoom in

1/72

www.gdts.one 452234.66.76 · FD 9912 EN-7

WI 140TUR+ English

7.2 Connection on heating and hot

water side

ATTENTION!

The heating system must be flushed prior to connecting the

heat pump.

Before completing the heat pump connections on the heating

water side, the heating installation must be flushed in order to

remove any impurities that may be present, as well as residues

of sealing material, and the like. Any accumulation of deposits

in the condenser may result in a total failure of the heat pump.

ATTENTION!

It is recommended that the secondary side be equipped with

the flow rate switch (available as an option).

ATTENTION!

It is recommended that the primary side be equipped with the

flow rate switch (available as an option).

Once the installation on the heating side has been completed,

the heating system must be filled, de-aerated and pressure-

tested.

Consideration must be given to the following when filling the

system:

Untreated filling water and make-up water must be of

drinking water quality

(colourless, clear, free from sediments)

Filling water and make-up water must be pre-filtered (pore

size max. 5 µm).

Scale formation in domestic hot water heating systems cannot

be avoided, but in systems with flow temperatures below 60 °C,

the problem can be disregarded. With high-temperature heat

pumps and in particular with bivalent systems in the higher per-

formance range (heat pump + boiler combination), flow tem-

peratures of 60 °C and more can be achieved. The following

standard values should therefore be adhered to with regard to

the filling and make-up water according to VDI 2035, sheet 1:

The total hardness values can be found in the table.

Fig. 7.1:Guideline values for filling and make-up water in accordance with

VDI 2035

For systems with an above-average specific system volume of

50 l/kW, VDI 2035 recommends using fully demineralized

water and a pH stabiliser to minimize the risk of corrosion in the

heat pump and the heating system.

ATTENTION!

With fully demineralized water, it is important to ensure that

the minimum permissible pH value of 7.5 (minimum

permissible value for copper) is complied with. Failure to

comply with this value can result in the heat pump being

destroyed.

Use of the optionally available four-way reversing valve is rec-

ommended. A detailed installation description can be found in

the instructions included with the valve.

Note:

For operation of the heat pump with the four-way reversing

valve, it is essential to set up the hydraulic connections accord-

ing to the instructions included in the scope of supply of the

valve. The instructions give a description of the precise proce-

dure for the correct assembly of hydraulics. Non-observance of

this will lead to restrictions in the operation of the heat pump.

Important:

The notes/settings in the instructions of the heat pump man-

ager must always be observed and carried out accordingly; not

doing so will lead to malfunctions.

Heating water minimum flow rate

The minimum heating water flow through the heat pump must

be assured in all operating states of the heating system. This

can be accomplished, for example, by installing either a dual

differential pressureless manifold.

Provided the heat pump manager and heating circulating

pumps are ready for operation, the frost protection feature of

the heat pump manager is active. If the heat pump is taken out

of service or in the event of a power failure, the system has to be

drained. In heat pump installations where a power failure can-

not be readily detected (holiday house), the heating circuit must

contain a suitable antifreeze product.

7.3 Connection on heat source side

The following procedure must be observed when making the

connection:

Connect the well pipes to the heat pump's flow and return heat

source.

ATTENTION!

It is essential that the dirt trap included in the accessories

pack is installed in the return (inlet).

ATTENTION!

The well water must comply with the required water quality

standards.

The hydraulic integration diagram must be adhered to.

Total heat

output in kW

Total alkaline earths

in mol/m³ and/or

mmol/l

Specific system volume

(VDI 2035) in l/kW

< 20 20 < 50 50

Total hardness in °dH

< 50 2.0 16.8 11.2

< 0.111

50 - 200 2.0  11.2 8.4

200 - 600 1.5 8.4 < 0.111

> 600 < 0.02 < 0.111

1. This value lies outside the permissible value for heat exchangers in heat

pumps.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex WI 140TUR plus in the language / languages: English, German, French as an attachment in your email.

The manual is 2.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex WI 140TUR plus Manual

Product: