Manual Dimplex SIW 11TES (page 24 of 76) (English, German, French)

798307

Zoom out

Zoom in

1/76

EN-2 452236.66.09 · FD 9912 www.gdts.one

English SIW 6TES - SIW 11TES

1 Please read immediately

1.1 Important information

ATTENTION!

When operating or maintaining a heat pump, the legal

requirements of the country where the heat pump is operated

apply. Depending on the refrigerant quantity, the heat pump

must be inspected for leaks at regular intervals by a certified

technician, and these inspections must be recorded.

ATTENTION!

If the heat pump or circulating pumps are controlled

externally, an flow rate switch is required to prevent the

compressor from being switched on when there is no volume

flow.

ATTENTION!

In installed and dismantled state, the heat pump module may

only be tilted by a maximum of 45° (in each direction) ( see

Cap. 5.3 on pag. 7).

ATTENTION!

Before start-up, the transport fastening must be removed.

ATTENTION!

Flush the heating system prior to connecting the heat pump.

ATTENTION!

The maximum test pressure in the heating circuit and the

brine circuit is 4.0 bar. This value must not be exceeded.

ATTENTION!

With fully demineralized water, it is important to ensure that

the minimum permissible pH value of 7.5 (minimum

permissible value for copper) is complied with. Failure to

comply with this value can result in the heat pump being

destroyed.

ATTENTION!

The brine solution must contain at least a 25 % concentration

of a monoethylene glycol or propylene glycol-based

antifreeze, which must be mixed before filling.

ATTENTION!

A suitable de-aerator (micro bubble air separator) must be

installed in the heat source circuit by the customer.

ATTENTION!

The heat pump must be started up in accordance with the

installation and operating instructions of the heat pump

manager.

ATTENTION!

The supplied dirt trap must be inserted in the heat source inlet

of the heat pump to protect the evaporator against the ingress

of impurities.

ATTENTION!

Work on the heat pump must only be performed by

authorised and qualified after-sales service technicians!

ATTENTION!

Disconnect all electrical circuits from the power source prior

to opening the device.

1.2 Intended use

This device is only intended for use as specified by the manu-

facturer. Any other use beyond that intended by the manufac-

turer is prohibited. This requires the user to abide by the rele-

vant project planning documents. Please refrain from

tampering with or altering the device.

1.3 Legal regulations and directives

This heat pump is designed for use in a domestic environment

according to Article 1, Paragraph 2 k) of EU directive 2006/42/

EC (machinery directive) and is thus subject to the require-

ments of EU directive 2014/35/EU (low-voltage directive). It is

thus also intended for use by non-professionals for heating

shops, offices, hotels and other similar working environments,

agricultural establishments and hotels, guesthouses and other

residential buildings.

This heat pump conforms to all relevant DIN/VDE regulations

and EU directives. Refer to the EC Declaration of Conformity in

the appendix for details.

The heat pump must be connected to the power supply in

compliance with all relevant VDE, EN and IEC standards. Any

further connection requirements stipulated by local utility com-

panies must also be observed.

The heat pump is to be connected to the heat source system

and the heating system in accordance with all applicable

regulations.

This unit can be used by children aged 8 and over and by per-

sons with limited physical, sensory or mental aptitude or lack of

experience and/or knowledge, providing they are supervised or

have been instructed in the safe use of the unit and understand

the associated potential dangers.

Children must not play with the device. Cleaning and user

maintenance must not be carried out by children without su-

pervision

ATTENTION!

When operating or maintaining a heat pump, the legal

requirements of the country where the heat pump is operated

apply. Depending on the refrigerant quantity, the heat pump

must be inspected for leaks at regular intervals by a certified

technician, and these inspections must be recorded.

More information can be found in the accompanying log book.

1.4 Energy-efficient use of the heat

pump

By operating this heat pump you are helping to protect our en-

vironment. Both the heating system and the heat source must

be properly designed and dimensioned to ensure efficient op-

eration. It is particularly important to keep water flow tempera-

tures as low as possible. All connected energy consumers

should therefore be suitable for low flow temperatures. Raising

the heating water temperature by 1 K corresponds to an in-

crease in energy consumption of approx. 2.5 %. Low-tempera-

ture heating systems with flow temperatures between 30 °C

and 50 °C are particularly well-suited for energy-efficient oper-

ation.

The domestic hot water temperature should not exceed 45 °C

when the heat pump is in operation. This will save you signifi-

cant amounts of energy.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SIW 11TES in the language / languages: English, German, French as an attachment in your email.

The manual is 2.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SIW 11TES Manual

Product: