Manual Dimplex SIH 40TE (page 22 of 52) (English, German, French)

798445

Zoom out

Zoom in

1/52

EN-8 452234.66.08 · FD 9602 www.dimplex.de

English

SIH 40TE

7.5 Electrical connection

7.5.1 General

All electrical connection work must be carried out by a trained

electrician or a specialist for the specified tasks in accordance

with the

installation and operating instructions,

country-specific installation regulations (e.g. VDE 0100),

technical connection conditions of the energy suppliers and

supply grid operators (e.g. TAB) and

local conditions.

To ensure that the frost protection function of the heat pump

works properly, the heat pump manager must remain connected

to the power supply and the flow must be maintained through the

heat pump at all times.

The switching contacts of the output relay are interference-sup-

pressed. Therefore, depending on the internal resistance of the

measuring instrument, a voltage can also be measured when the

contacts are open. However, this will be much lower than the line

voltage.

Extra-low voltage is connected to controller terminals N1-J1 to

N1-J11; N1-J24 to N1-J26 and terminal strip X3; X5. If, due to a

wiring error, the line voltage is mistakenly connected to these ter-

minals, the heat pump manager will be destroyed.

7.5.2 Electrical installation

1) The electric supply cable for the output section of the heat

pump (up to 4-core) are fed from the electricity meter of the

heat pump via the utility blocking contactor (if required) into

the heat pump (see the device information for supply volt-

age).

Connection of the mains cable to the control panel of the

heat pump via terminal X1: L1/L2/L3/PE.

ATTENTION!

Ensure the rotary field is clockwise when connecting the mains cables (if

the rotary field is not clockwise, the heat pump will not work properly, is

very loud and may cause damage to the compressor).

An all-pole disconnecting device with a contact gap of at

least 3 mm (e.g. utility blocking contactor or power contac-

tor) and an all-pole circuit breaker with common tripping for

all external conductors must be installed in the power supply

for the heat pump (tripping current and characteristic in com-

pliance with the device information).

2) The three-core electric supply cable for the heat pump man-

ager (heating controller N1) is fed into the heat pump . Con-

nection of the control line to the control panel of the heat

pump via terminal X2: L/N/PE.

The (L/N/PE~230 V, 50 Hz) supply cable for the heat pump

manager must have a constant voltage. For this reason, it

should be tapped upstream from the utility blocking contac-

tor or be connected to the household current, as important

protection functions could otherwise be lost during a utility

block.

3) The utility blocking contactor (K22) with main contacts and

an auxiliary contact should be dimensioned according to the

heat pump output and must be supplied by the customer.

The NO contact of the utility blocking contactor is looped

from terminal strip G/24 V AC to connector terminal J5/ID3.

CAUTION! Extra-low voltage!

4) The contactor (K20) for the immersion heater (E10) of mono

energy systems (HG2) should be dimensioned according to

the radiator output and must be supplied by the customer. It

is controlled (230 V AC) by the heat pump manager via ter-

minals N and N1-J13/NO4.

5) The contactor (K21) for the flange heater (E9) in the hot

water cylinder should be dimensioned according to the radi-

ator output and must be supplied by the customer. It is con-

trolled (230 V AC) by the heat pump manager via terminals

N and N1-J16/NO 10.

6) The contactors mentioned above in points 3, 4 and 5 are in-

stalled in the electrical distribution system. Mains cables for

the installed heaters must be laid and secured in accord-

ance with the valid standards and regulations.

7) All installed electric cables must have permanent wiring.

8) The heat circulating pump (M13) is connected to N1-J13/

NO5 and X2/N. When using pumps where the switching ca-

pacity exceeds the output, a coupling relay must be inter-

posed.

9) The auxiliary circulating pump (M16) is connected to N1-

J16/NO9 and X2/N. When using pumps where the switching

capacity exceeds the output, a coupling relay must be inter-

posed..

10) The domestic hot water circulating pump (M18) is connected

to N1-J12/NO6 and X2/N. When using pumps where the

switching capacity exceeds the output, a coupling relay must

be interposed.

11) The brine or well pump (M11) is activated via the contact N1-

J12/NO3. The connection points for the pump are on contac-

tor K5:2/4/6. A coupling relay is already integrated in this

output.

12) The return sensor (R2) is integrated into heat pumps for in-

door installation.

The heat pump manager is connected via the following ter-

minals: GND and N1-J2/B2.

13) The external sensor (R1) is connected to terminals GND and

N1-J2/B1.

14) The domestic hot water sensor (R3) is included with the do-

mestic hot water cylinder and is connected to terminals X3/

GND and N1-J2/B3.

The power cable must be run through the guide tubes, inserted

into the side of the control box and secured by means of the

strain relief.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dimplex SIH 40TE in the language / languages: English, German, French as an attachment in your email.

The manual is 2.09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dimplex SIH 40TE Manual

Product: